Engineering Fundamentals Quiz
Engineering Fundamentals Quiz
Test your knowledge on crucial engineering principles and regulations with our engaging quiz. Perfect for students and enthusiasts alike, this quiz is designed to challenge your understanding while providing valuable insights into technical standards.
- Multiple-choice questions
- Focus on engineering rules and regulations
- Designed for learners and professionals
Which of the following is TRUE ?
Front bulkhead – A planar structure that defines the rearward plane of the chassis and provides protection for the driver's feet.
Sliding skirts or other aerodynamic devices that by design, fabrication or as a consequence of moving, contact the track surface are not prohibited.
The student team may use any information from professionals or from academics as long as the information is given as a discussion of alternatives with their pros and cons.
Both A&B
Which of the following is FALSE ?
Enclosed chassis structures and structures between the chassis and the ground must have two venting holes of at least 25 mm diameter in the lowest part of the structure to prevent accumulation of liquids. Additional holes are required when multiple local lowest parts exist in the structure.
The vehicle must be equipped with fully operational front and rear suspension systems including shock absorbers and a usable wheel travel of at least 50 mm and a minimum jounce of 25 mm with driver seated.
Both A&B
None of these
Which of the following is TRUE ?
Rear wheel steering, which can be mechanically actuated, is permitted if electrical stops limit the range of angular movement of the rear wheels to a maximum of 6°. This must be demonstrated with a driver in the vehicle and the team must provide the equipment for the steering angle range to be verified at technical inspection.
The maximum restrictor diameters which must be respected at all times during the competition are : Gasoline fueled vehicles - 25mm
The temperature of fuel introduced into the fuel system may not be changed with the intent to improve calculated efficiency.
None of these
Which of the following is FALSE ?
The officials may inspect other points not mentioned on the technical inspection sheet to ensure compliance with the rules.
The top teams from Class II will be judged BPP finals at the competition. The teams will be notified at least 2 weeks before the competition dates.
The scoring of the BPP finalists will vary from 75 to 71 points and is scored immediately after the BPP finals by all judges.
CHECKERED FLAG – The session has been completed. The driver must exit the course at the first opportunity.
Which of the following is TRUE ?
Burnouts after and during the events are prohibited.
Prior to the competition, the team must submit a pitch deck and participate in an offline presentation delivery.
None of these
Off-course (OC)
An OC occurs when the vehicle has all four wheels outside the course boundary as indicated by edge marking.
Missing one or more gates of a given slalom at autocross or endurance is counted as one OC per occurrence.
When re-entering the driver needs to wait for a gap and follow the instructions of the track marshals.
All of the above
Which of the following is TRUE ?
Should the fuel level change after refueling due to effects such as described in CV2.7.1, then the difference in fuel level will be measured and twice the amount will be added to the official fuel consumption figure.
TMI – No submission of TMI by deadline will not result in team members‟ inability to receive electronic certificates and participate in on-site event.
No response to official‟s communication on delayed or non-submission of the documents shall result in de-registration of the team from the competition.
Both A & C
Which of the following is FALSE ?
Any portion of the roll bar, roll bar bracing or chassis which might be contacted by the driver's helmet must be covered with a minimum thickness of 12 mm of padding which meets SFI spec 45.1 or FIA 8857-2001.
Implausibility is defined as a deviation of more than ten percentage points pedal travel between any of the used APPSs or any failure according to T11.9.
None of these
The maximum allowed delay of messages according to T11.9.2.d must be chosen depending on the impact of delayed messages to the connected system, but must not exceed 100ms.
Which of the following is TRUE ?
All edges of the bodywork that could come into contact with a pedestrian must have a minimum radius of 1 mm.
There is a minimum tread depth of 2.4 mm.
Both A&B
None of the above
Which of the following is FALSE ?
Sensors and components may not come into contact with the driver‟s helmet under any circumstances.
Berufsakademie → BA
Crankcase breathers that pass through the oil catch tank(s) to exhaust systems, or vacuum devices that connect directly to the exhaust system, are prohibited.
None of these
Which of the following is TRUE ?
The available fuel types will be unleaded gasoline 91 Octane.
Separate catch cans must be employed to retain fluids from any vents for the coolant system or engine lubrication system. Each catch-can must have a minimum volume of 10% of the fluid being contained or 100 ml whichever is greater.
Nylon lock nuts (ISO 7040, ISO 10512, EN 1663 or equivalent) for low temperature locations (90 deg C or less)
Both B&C
Which of the following is FALSE ?
Teams must bring a copy of the approved SES to technical inspection.
The SES spreadsheet form can be downloaded from the competition brochure
The bodywork in front of the front wheels must have a radius of at least 38 mm extending at least 45° relative to the forward direction, along the top, sides and bottom of all affected edges.
Both A&C
Which of the following is TRUE ?
Incorrect file type: 5 penalty points
Missed Presentation Session with less than 48 hour notice: 50 points
Exceeding time limit: 10 penalty points
All of these
Which of the following is FALSE ?
Team members must be at least 18 years of age.
Team members who will drive a competition vehicle at any time during a competition must present an invalid, government issued driver‟s license for passenger cars, containing a photograph.
All onsite participants under 18 years of age must submit the Under 16 liability waiver prior to the competition. This shall be made available via the competition website.
All of these
Which of the following is TRUE ?
A team member may only be part of one team, work on two vehicle and take part in static and dynamic events for only one team.
Students who have already graduated from a degree program and are seeking another degree of the same level or below are not allowed to participate.
Team members must be enrolled as degree seeking undergraduate or graduate students in any university. Team members who have graduated within the twelve month period prior to the competition remain eligible to participate.
Both A&C
{"name":"Engineering Fundamentals Quiz", "url":"https://www.quiz-maker.com/QPREVIEW","txt":"Test your knowledge on crucial engineering principles and regulations with our engaging quiz. Perfect for students and enthusiasts alike, this quiz is designed to challenge your understanding while providing valuable insights into technical standards.Multiple-choice questionsFocus on engineering rules and regulationsDesigned for learners and professionals","img":"https:/images/course8.png"}