Tommy is driving the Endurance for the Spark Light team. While the driver change, Tommy is jumping out of the car while it is not fully stopped. Jaquelin and Sally is stopping the car with her hands while Mustaffa the next driver is seeing a blinking red

Tommy is driving the Endurance for the Spark Light team. While the driver change, Tommy is jumping out of the car while it is not fully stopped. Jaquelin and Sally is stopping the car with her hands while Mustaffa the next driver is seeing a blinking red light as he assumed as the TSAL. The judge close to the Team signaled DNF. What was the matter?

Nobody is allowed to touch the car as long the TSAL is not indicating a green light

The driver has to push the shut down button when he is entering the driver change area

There are no more then 1 Person additional to the Drivers allowed in the restricted zone while the driver change

Jaquelin is not an ESO

A hydraulic lifting platform with a max. Capacity of four tons operates at a system pressure of 350 bar. It is capable of lifting a car with a weight of 4500 lb to a height of six and a quater feet above the ground within 32 seconds. Calculate the minimum flow rate of the hydraulic fluid at the pump exit in ml/s. At an efficiency of 82%, how much power (in kW) is required to run the hydraulic pump? Round to two decimal places. G is 9,81 m/s²

66,74 ml/s and 1,19 kW

66,74 ml/s and 2,34 kW

50,40 ml/s and 3,02 kW

66,74 ml/s and 1,45 kW

You want to shrink fit a shoulder bolt (DIN 609, Steel, size M8x40) into your titanium (3.7165) upright (T=20°C). The Diameter of the bore in the upright is 9 N7. The CTE of the titanium alloy is 9,4E-6 and the steel has a CTE of 12E-6. The Bolt is at a temperature of 30°C. What is the minimum temperature to which you have to heat the upright so that the bolt will slide in the bore guaranteed? In your calculations, round the diameters to 3 decimal places

59,1°C

375,4°C

363,5°C

333,5°C

If critical fasteners are secured with a lock nut, what is the minimum number of full threads that must project from this lock nut?

There is no limitation regarding the minimum number of full threads.

One full thread

Two full threads

Three full threads

Which is the minimum specification for threaded fasteners utilized in the driver’s cell structure, and the steering, braking, driver’s harness and suspension systems?

Grade 6.8

Grade 8.8

Grade 10.9

Grade 12.9

Which modification to the car is not allowed without rescrutineering?

Changing of the steering wheel

Adjustment of the wing angle

Changing the springs of the suspension system

Replacing worn brake pads

What of the following statements is right

Low voltage batteries must be attached securely to the chassis

The university name must be displayed and written in Roman Sans-Serif characters of at least 55 mm high on both sides of the vehicle.

The hot (ungrounded) terminal must not be insulated

The lifting of the vehicle with the quick jack must be possible by one person and not require actions other than positioning and operating the quick jack itself

What is the minimum overall firefighting capacity of the fire extinguisher with the right ratings for Europa

2.2kg 5A

1.8kg 20BE

1.8kg 34B

0.9 kg 34B

While scrutineering the judge is confused and needs to look up a few rules to the TSMP. What is the correct setup for the TSMP due to the rules? Car maximum TS Voltage: 201 VDC

4 mm shrouded banana jacks of rated for 1000 V CAT III or better must be used for the TSMPs

The resistor value is 10kΩ. The TSMP´s are marked with TS+ and TS- on an red backround and the GLVS next to it is a 4mm black shrouded banana jack

The TSMP´s are marked with TS+ and TS- red backround and the GLVS next to it is a 4mm black shrouded banana jack.

The TSMP´s are marked with TS+ and TS- on an orange backround and the GLVS next to it is a 4mm red shrouded banana jack

Unlock and Upgrade

Remove all limits from your Quizzes

More Quizzes