CIVL401 - Introduction to Capstone
CIVL401 Capstone Quiz
Test your knowledge in Civil Engineering with our comprehensive CIVL401 Capstone Quiz. This quiz encompasses various critical topics, providing a challenging experience that sharpens your understanding of key concepts.
Key Features:
- 21 well-structured multiple-choice questions.
- Assessments covering various civil engineering topics.
- Instant feedback on your performance.
Which of the following best describes safety requirements in strength method of RC section design?
Stresses in RC beams should not exceed the allowable stress limits.
RC sections are designed by considering the elastic stage under the action of factored load effect.
Failure stage of a section should be considered that section capacity determined by reduced material strength should be greater than the factored load effect.
Section should be strong enough to resist any external disturbance.
None of the above.
In Slope Deflection Method (by neglecting axial deformations) the degrees of freedom of the beam given below are,
θA, θB and θC
θB and θC
θB, θC and θD
A) θA, θB, θC and θD
θD
Which of the following is NOT the definition of sustainability?
Capacity of being maintained at a steady level without exhausting natural resources.
Is the method using a resource so that the resource is not depleted or permanently damaged.
Not being able to maintain balance of a certain process in any system.
An investment in any system of human living.
Includes concerns related to environmental, related to environmental economic and social.
Speed is reduced when super elevation rate is remained constant and radius of curvature is:
Decreased.
Increased.
Does not change.
Both increased and decreased.
None of the above.
Which one of the following is a disadvantage for owning equipment?
Requires initial cost.
Prestige of owning equipment.
Full control of equipment resources.
Availability when needed.
Governmental tax incentives and investment credit.
The hydrostatic force generated by a column of fluid depends on:
Velocity of fluid.
Temperature of fluid.
Depth of fluid.
Viscosity of fluid.
None of the above.
Which are the highest two types of solid waste per year in North Cyprus?
Household and Municipal.
Construction and Industrial.
Industrial and Commercial.
Construction and Green.
Municipal and Construction.
If the current effective stress is less than the pre-consolidation stress, then the soil is said to be:
Normally consolidated.
Over-consolidated.
Consolidated.
Under consolidated.
Not consolidated.
In EIA report pollution section, which one of the below topics is NOT discussed in detail?
Water.
Human Population Density.
Sound.
Soil.
Air.
Workability is affected by some factors. One of these major factors is,
Water content of the mix.
Roughness of the mix.
Quality of cement in the mix.
Toughness of the mix.
Resistance of the mix.
What are the elements of equipment cost?
Straight line method, double declining balance method; sum of the year’s digits method.
Owning cost, fuel cost, operator’s wage, insurance.
Tax liability, capitalized cost, installation cost, salvage value.
Owning cost, depreciation, investment cost, insurance, tax, and storage.
None of the above.
For the frame given below; support B will have 6 mm displacement in a downward direction. In solution with Slope Deflection Method, in which members chord rotation angles will be calculated?
AC and BD.
CD, DE, and BD.
AC, CD and DE.
CD and DE.
BD.
Name three apparatuses used in the initial and final setting times.
Stand, Sieve, Tray.
Plate, Buckling, Cleaning.
Cone, Balance, Scoop.
Vicat, Cylindrical disc, Plunger flask.
Wire basket, Balance, Flask.
Within the Environmental Inventory Control which one is NOT among the main topics?
Human population.
Biologic.
Cultural.
Physical/Chemical.
Socio-economic.
The behavior of soil during one-dimensional loading can be tested using a device called:
Compactor.
Permeameter.
Oedometer.
Vane shear.
Sand cone.
What are the activities of earth moving?
Excavation and loading.
Hauling and damping.
Spreading and compacting.
Grading and finishing.
All of the above.
Mass diagram is used for obtaining:
Fill volume.
Cut volume.
Borrow or waste.
Free haul distance.
Cross-sectional area.
According to conservation of mass,
Inflow velocity is equal to outflow velocity.
There is no change in velocity with respect to time.
Net inflow into the system must be equivalent to net outflow.
The density of fluid must be constant.
All of the above is correct.
{"name":"CIVL401 - Introduction to Capstone", "url":"https://www.quiz-maker.com/QPREVIEW","txt":"Test your knowledge in Civil Engineering with our comprehensive CIVL401 Capstone Quiz. This quiz encompasses various critical topics, providing a challenging experience that sharpens your understanding of key concepts.Key Features:21 well-structured multiple-choice questions.Assessments covering various civil engineering topics.Instant feedback on your performance.","img":"https:/images/course8.png"}