PAMPASA NG FE

In accordance with the requirements of Geotechnical investigation, what is the minimum number of boring shall be provided for piers or abutments over 30m wide?

For school buildings, all slab reinforcements shall be ____ minimum for bottom and top slab

For school buildings, camber all beams and girder atleast 6mm every ___ span, except cantilevers for which the camber shall be as noted in the plans but no case less than 20mm for every ____ span

For school buildings, all embedded pipes for utilities etc. That pass thru beams shall not exceed ____ in diameter or 1/3 beam depth width whichever is less

What is the maximum free height of the PVC sheet pile for revetments to limit potential deflection

What method is usually adopted when there is no visible evidence of termite infestation during soil poisoning?

What method is usually adopted when there is visible evidence of termite infestation during soil poisoning?

For pre-painted metal sheets what is the minimum end laps that shall be provided?

Warranty period for permanent structures as per RA 9184

What is the minimum headroom between the pedestrian walking surface and bottom of girder of the structure like railway, flyover and bridge above shall be ____

What is the minimum vertical clearance above road carriageway for flyovers, bridges and railways?

What is the minimum vertical clearance above road carriageway for pedestrian footbridges?

Advance payment to the contractor in an amount not to exceed ___ of the total original contract amount

Withholding VAT for progress billing of the contractor shall be?

Total amount of liquidated damages shall be deducted to the _____

It reflects accomplishment-duration relationship in the project

It is the graphical representation of the cumulative monthly cash flow of a project over its time duration

Contract time extension may be granted only when the affected activities fall within the ____ of the PERT/CPM or PDM network

It is the difference between the targeted accomplishment and the actual accomplishment at the end of a certain period, it is expressed in percentage and indicates the performance of project implementation

One eligibility requirement for contractors is to be a Filipino Citizen or at least ____ Filipino owned partnership or corporation

What is the design life span of permanent bridges before it is being replaced?

What do you call the clearance between the design flood level (DFL) or the maximum experienced flood level (MEFL) and the (soffit) of the lowest member of the bridge superstructure?

This is very suitable for shallow foundation and for areas wherein the hard strata lie 3m below the NGL for firm materials and 5m below the NGL for soft materials

This is equal to the tip elevation minus the "cut-off elevation" or bottom elevation of the pile cap.

What is the maximum allowed span length for reinforced concrete deck girder?

What is the suggested type of pre-stressed girder to be used when the span length is 35m?

What is the suggested type of pre-stressed girder to be used when the span length is 18m?

What is the maximum jacking force for pre-stressed girders?

MEFL means Maximum ____ Flood Level

Dike height = free board + ____

Generally, what is the minimum freeboard allowance above the MEFL and DFL Revetments?

Minimum overall thickness should be ___ for all types of revetment, except for reinforced concrete type.

What is the maximum span length of spur dike?

Groundsill are structures constructed ____ to the flow of the river

For creeks in urban and rural areas and not subject to overbank flows, a minimum easement to be provided measured from the edge of the existing bank or the improved bank should be ____

River, esteros and navigating canals, not subject to overbank flows should have a minimum easement measured from the edge of the existing bank or the improved bank of ____

This is where the computation of contract price escalation of a project that is awarded thru "public bidding" should be based and reckoned.

This is where the computation of contract price escalation of a project that is awarded thru "simplified bidding" should be based and reckoned.

In horizontal alignment of roads and highways, what is the maximum algebraic difference of cross-over?

For roads and highways, what is the minimum recommended width of curve widening?

What is the validity / renewal period of the PE accreditation?

The spacing of the bars at the column strips for school building shall not be more than ____ slab thickness

Statement: No pipes shall be embedded in columns of the school building

Statement: No pipes shall be allowed to pass thru beams of the school building vertically

Statement: Splicing of PVC sheet piles for revetments shall be allowed

For combination of bored/steel sheet pile for bank protection, what is the minimum N-value capable developing the required ultimate bearing capacity?

What is the minimum end laps for corrugated metal roofing?

As per RA 9184, rule IX what is the warranty period for semi-permanent structures or building types 1, 2, and 3

What is the durometer hardness for elastomeric bearing pads which is 100% virgin chloroprene (neoprene) pads?

In rural areas, what is minimum bridge pedestrian width

In urban areas, what is minimum bridge pedestrian width?

What is the maximum height of bridge abutment

For service load design of bridges, what is the flexural stress in the extreme fiber stress in compression?

For effective drainage, the slope of edge of pavement shall be less than or equal to ___ between +-1.5% grade

What is the cross slope of the higher shoulder for roads and highways when the super elevation is 4%?

What is the cross slope of the higher shoulder for roads and highways when the super elevation is 5%?

What is the minimum depth of roadside channel from the bottom of pavement?

What is the minimum width of PCCP on National Highways per lane?

What is the minimum width of PCCP on farm to market roads per lane?

What is the minimum length of the radius of horizontal curve for PCCP on farm to market Roads?

What is the minimum diameter size of pipe culverts?

In an emergenct, the head of the procuring entity may authorize a Variation order beyond 10% but not more than ____ of the original contract price following the guidelines determined by Government Procurement Policy Board (GPPB)

Processing of advance payment shall require that minimum of ____ of the scope of work should be workable or free from obstruction

Early warning stage happens when the negative slippage of the project accomplishment is ___?

ICU stage happens when the negative slippage of the project accomplishment is ___?

Terminal Stage happens when the negative slippage of the project accomplishment is ___?

During bidding, the bidder may sub-contract a material or significant portion of the goods which must not exceed ____ of the contract price

The BAC shall determine to its satisfaction where the bidder that is evaluated as having submitted the ____ complies with and is responsive to all requirements and conditions

What do you call the overlap between the first and second activity in PERT CPM/PDM

It is measured from back of backwall to back of backwall of the bridge

It is a temporary wall installed to exclude water to allow construction work within the are protected by the _____.

It provides access for equipment to the location of the foundation of the bridge.

There are rectangular piles which can take huge axial loads and high moments, ideal for boulder ground and alluvial soil but adaptable to most type of ground

The main objective of the ____ dynamic test is to determine pile bearing capacity

Statement: pouring permit for PCCP is the same from pouring permit on bridge structures.

When borehole drilling using super mud, what is the pH range of pre-treat water with soda ash?

What is the minimum head pressure required to drill when borehole drilling using super mud?

When concreting of bored piles, overpouring in the quantity of ___ of the theoretical volume is considered "in order"

What is the diameter of the High tensile strand used in pre-stressed concrete girders?

What do you call the bridge with superstructure perpendicular to its substructure?

What do you call the bridge with superstructure NOT perpendicular to its substructure?

A change order may be issued when the aggregate cost is limited to ____ of the original contract cost,

What is used to emphasize to the approaching driver a marked change in the direction of travel and the presence of an obstruction

On simple curves, widening of curves should be applied on the edge only.

The revision length of tangent between reversed curve should be 50mm and in no case, should be less than ____.

Gradients/grades of roads, highway and bridges should be as ___ as possible

Vertical alignment of roads shall require that for every degree of curvature six degrees, the ruling grade shall be reduced by ____

Which of the following is not a classification of a terrain?

What is the vertical alignment scale for the road plan preparation?

What is the horizontal alignment scale for the road plan preparation?

What is the minimum preferred slope on pipe culverts?

Pipe culverts shall be laid at such grades that there will be a cushion of at least ___ of fill over the top of the pipe.

What is the maximum allowable grade for national roads?

What is the length of the road widening from center of the road left and right side for national roads?

What is the length of the road widening from center of the road left and right side for municipal roads?

What is the length of the road widening from center of the road left and right side for barangay roads

What is the minimum travelled way for provincial roads?

What is the minimum road right of way (RROW) for national roads?

What is the minimum road right of way (RROW) for municipal roads?

What do you call the depth of water above the culvert inlet bottom?

What do you call the depth refers to the total depth of water from surface to a purged bed level?

What is the range of Spur dike's top width?

For concave sections, why is the distance between spur dikes times the length of spur?

For convex sections, what is the distance between spurdikes times the length of spur (LS)

What is the minimum Radius of curve for a design speed of 30kph?

What is the minimum bandwidth of the reflective tapes for traffic cones?

What is the standard maximum height for traffic bollards?

Concrete barrier need to be continuous to be continuous or secured together, generally using steel pins and eyelets, with a maximum ___ gap to ensure they perform satisfactorilly

What is the standard distance range of road warning signs in advance of the construction site for urban areas?

What is the standard distance range of road warning signs in advance of the construction site for rural areas?

Barrier boards shall not be used for delineation purposes or installed parallel to vehicular traffic unless there is an offset of atleast ___ from the travelled path

Traffic cones shall be spaced ___ apart on tapers and around small work sites.

What kind of reports are used to document events that occur at a plant or operation, such as concrete batch plant or bituminous plant?

These are monthly or quarterly statements of time and cost for the project. The report documents all changes that have accrued since the beginning of the project regarding time and cost

What kind of report are used to summarize the work progress for the immediate preceding month or quarter. Usually contains a narrative section describing status of project, s-curve diagram summary of contract time and change orders?

What kind of report are used to document any corrective changes which occur in the field that would require departure from the plans and specifications and then provide the necessary information to understand the problem, decide of how to resolve it and issue instructions to the field and serve as a source of document for variation order approvals?

After the issuance of the punch list during the pre final-inspection, ____ months-time duration imposed to complete the project without penalties.

This represents the payment of the remaining balance of the contract including the total retention after the completion of the project

The contractor will be allowed to file for the release of first partial billing if he had satisfactorily completed atleast ____ of the contract amount

When the spread footing location on a slope, the minimum distance from the lower edge of the footing to the sloping ground surface should be ____

What is the maximum spacing center to center of adjacent rings of circumferential reinforcement in a cage of standard two-meter RCPC?

For school buildings, footing shall rest atleast ____ below natural grade line.

For buildings, the minimum concrete protection for reinforcement shall be ____ clear for concrete deposited the ground.

For buildings, the minimum concrete protection for reinforcement shall be ____ clear for concrete deposited a formwork.

What is the minimum days of stripping of forms and shores for suspended slab in school building?

What is the minimum days of stripping of forms and shores for walls and columns in school building?

This is the guidelines on the accreditation of the contractors and consultant's project engineer

What is the minimum girder required for a one lane bridge?

What is the minimum girder required for a 2-lane bridge?

Construction joints in floors hall be located within the ____ of spans of slabs, beams, and girders. Joints in girders shall be offset a minimum distance of two times the width of intersecting beam.

All embedded pipes for utilities etc. That pass thru beams shall not exceed 100mm in diameter or beam depth whichever is less, and no pipes shall be allowed to pass thru beams vertically.

The ACI code gave a provision on structural integrity to perimeter beams is to splice continuous top bars at ___ and splice continuous bottom bars at or near supports

All doors for people with disability (PWD) shall have minimum clear width of ____ meter

All sidewalks/walkways for people with disability (PWD) shall have a minimum clear width of ___ meter

As per IRR 344, handrails attached to walls should have a clearance no less than ___ from the wall

All sidewalks / walkways for people with disability (PWD) shall have a maximum grade of?

No vertical curve is required when algebraic difference between grades is less that _____

What do you call the discharge used to size the capacity of the bridge?

What is the maximum spacing of bridge drains?

What is the minimum diameter of bridge drains?

What is maximum design span for box girders?

What is the minimum design thickness for asphalt overlay projects?

What is the minimum STE individual years of experience for Class A Category AA Contractor

What is the maximum allowable single project cost for Small B Category C contractor?

What is the maximum allowable contract cost for medium A category B contractors?

What is the minimum width of turnouts, loading and unloading bay, to accommodate all types of vehicles

What is the standard color for all DPWH steel bridges?

National Numbering system (NRS) should remain over the medium term and reviews shall be undertaken on a periodic ____ cycle.

What is the minimum width of Zebra (Longitudinal bars) for pedestrian crossing markings?

Pedestrian crossing markings at road intersection without channelization islands shall be placed outside the intersection area at least ____ set back from the edge of the road

Who is the approving official if the work suspension order is 85 calendar days?

What is the standard dimension for Project Billboard?

For road projects with length of 10 kilometers or more, additional billboard shall also be installed at every ____ interval.

No other billboards shall be allowed to be installed __ before and after all DPWH projects and in-between the project limits or within the road right-of-way.

It is acceptable for "A-Built Plans" as a reason for final variation order of the cumulative increase in value of work does not ___ of the adjusted original contract price.

What is the maximum amount for Regional Directors to approved Program of Work, ABC and plans like as-built and as-staked?

What is the maximum amount for "selected" District Engineer to approved Program of Work, ABC and plans as-built and as-staked?

What is the maximum amount for "ALL" District Engineer to approved Program of Works, ABC and plans as built and as-staked?

What is the minimum pavement thickness for Farm to Market Roads?

What is the minimum Radius of Horizontal Curve for Farm to Market Roads?

What is the minimum Radius of Horizontal Curve for Tourism Roads?

The RROW boundary marker posts shall be installed along the RROW limit line on each side of the road at __ kilometer interval.

On highly urbanized area, RROW marker shall be concrete block embedded on the surface along the edge of concrete sidewalk on each side of the road at ___ interval.

All permanent bridges along national roads shall be provided with the Informative signs to be posted on conspicuous place within ___ before the abutment at both approaches.

What is the negative slippage for "ICU Stage"?

What is the negative slippage for "Terminal Stage"?

What is the maximum distance outside the shoulder for Kilometer Post from the edge of the road pavement?

If a shoulder is less than 2.0m, what is the setback distance of the Kilometer Post from the edge of the shoulder?

What is the spacing of dowels bars for 280 mm thick PCCP?

What is the spacing of dowels bars for 300 mm thick PCCP?

Vertical Clearance for Bridges over Navigable Waterways is the sum of Highest Water Level (HWL) and Height of Vessel (HV) and the K Factor. What is the constant value of the K-factor?

Contractor shall shoulder all the expenses for the alteration and/or reconstruction of the structure and a fine of ___ of the original total contract price, if they violated the minimum Vertical Clearance for Bridges over Navigable Waterways.

What is the setback distance from the RROW Limit for Welcome Arches and Overhead Boundary Markers?

For span lengths of 21-30 meters, what bridge type shall be use as per Department Order No. 30 Series of 2011?

For span lengths of 6-12 meters, what bridge type shall be use as per Department Order No. 30 Series of 2011?

Which pf the following contractor category is not required for ISO 9000 Certification?

What is the minimum individual years of construction experience for Sustaining Technical Employee (STE)

What is the minimum individual years of construction experience for Sustaining Technical Employee (STE) for all Classes and Categories of a Contractor?

What is the minimum Financial Capacity, Net Worth/Equity of a Class A Category A Contractor in Pesos?

What is the minimum Financial Capacity, Net Worth/Equity of a Class A Category AAAA Contractor in Pesos?

What do you call the project scheduling Technique used for DPWH Projects?

If the actual soil bearing capacity of the natural ground is less than 96 kPa at depth of 1.5m, what is the maximum depth of the isolated footing?

What is design Speed for Flat Terrain of Tourism Roads?

What is design Speed for mountainous terrain of Farm to Market Roads?

What is design Speed for Flat terrain of Farm to Market Roads?

What is the roadway cross slope for PCCP?

What is the roadway cross slope for gravel surfacing of sidewalk?

It is the physical island at the center of a divided roadway separating traffic flows.

It is designed to control and direct traffic movement, usually turning.

As a minimum requirement for Bridge projects __ bored pile(s) shall be tested representing each pile size.

For buildings, at least __ of the total number of bored piles shall be tested.

As per BP 344, Handrails attached to walls should have a clearance no less than 50mm from the wall and handrails on ledges should have a clearance not less than __.

What is the minimum raised height required for signages/symbols labeling public rooms and places?

To guide the blind, sidewalks should as much as possible follow straight forward routes with __ angle turns.

What is the minimum width of the refuge island and its total total length?

The Refuge island shall be provided in roadways having clear carriageway width of at least __ lanes.

What is the flood flow velocity criteria in designing slope protection works?

What is the minimum desirable length of Turnouts, unloading and loading bays, on national roads?

What is the maximum length of Turnouts, unloading and loading bays, on national roads?

If the actual soil bearing capacity of School Building did not meet the required 96 kPa soil bearing capacity, the implementing office may opt to perform/use the following except one:

What is the width of the Stop Line in Urban Roads?

What is the width of the Stop Line in Rural Roads?

When using Reclaimed Asphalt Pavement (RAP) as partial replacement to coarse aggregate in Hot-Mix Asphalt (HMA), what is the maximum % for Item 320 Grading D and Grading B?

If the actual condition of the soil in school building is susceptible to liquefaction , ground improvement technique may be performed except one;

The minimum Bridge Carriageway width for Tourism Roads.

The minimum Bridge Carriageway width for 5.0m width - Farm to Market Roads.

The minimum Bridge Carriageway width for 6.1m width - Farm to Market Roads.

What is the flood frequency used in hydraulic analysis for bridge design?

For Pre-Cast Concrete Curb and Gutter, minimum curb inlet interval (D) is __ in flooded areas and ___ in other areas.

For multi-span bridges, Pile Bearing Capacity Test shall be conducted ___ at each abutment and 1 at every other pier.

Pile Integrity Test shall be conducted on at least ___ of the total number of bored piles at each abutment and pier of bridges or at the entire foundation area of buildings.

Cross hole Sonic Logging Test (CSL) is recommended for bored piles with embedded length of more than ___.

What is the minimum width of a curb cut-out?

When the AADT is greater than ___ vehicles, paving of shoulder is necessary.

Minimum distance between two consecutive pedestrian refuge islands along the highway shall not be less than ___ meters.

What is the Navigational Clearance of a bridge over navigable waterways with the given data: HWL=15.0m and HV=10.0m

If the length and width of the drainage area is equal to 50m and 100m respectively; what should be the length of the channel?

Compute the amount of Liquidated Damages (LD) given the following data: Remaining scope of work amount is PHP 1,000,000.00 and the contractor completed the remaining scope of work in 15 calendar days time

Defects Liability Period

As per RA 11058, the General Contractor must provide one (1) Construction Safety and Health Officer for every ___ units of Heavy Equipment assigned to the project site to oversee the effective compliance with the COSH Program.

What is the maximum gradient for Curb Cut-Outs?

What is the maximum gradient for sidewalk as per BP 344?

As per BP 344 requirement, what is the walking speed design on the crossings?

What is the length of tangent between reverse curves for both tourism and farm to market roads?

For roadway obstructions, such as bridge piers, what is the width of the black and white stripes on the object marking?

For roadway obstructions, such as bridge piers, what is the minimum width of the black and white stripes on the object marking?

For raised median island, planting of trees should not be permitted on Highspeed multilane divided highway and the surface level of soil fill shall be lower than the top of island - 50mm for island height less than or equal to ___ and 10mm for island height greater than ___

The pavement thickness of turnout, unloading and loading bays, shall in no case be less than ___ for asphalt and 230mm for concrete with supporting base layers.

During road re-blocking works, holes of ___ diameter and spaced at 300mm shall be drilled at 1/2 of the existing concrete pavement thickness to permit the load transfer transverse construction joint.

The procuring entity shall, upon a written request of the contractor which shall be submitted as a contract document, make an advance payment to the contractor in an amount not exceeding blank percent of the total contract price?

The advance payment shall be repaid by the contractor by deducting fifteen percent from his payments on

This is issued by the procuring entity to cover any increase/decrease in quantities, including the introduction of new work items that are not included in the original contract.

May be issued by the implementing official to cover any increase/decrease in quantities of original work items in the contract.

May be issued by the implementing official to cover the introduction of new work necessary for the completion, improvement or protection of the project which was not included as items of work in the original contract.

An amount equal to one-tenth of one percent of the cost of the unperformed portion of the works for every day of delay.

Total sum of liquidated damages shall not exceed blank percent of the total contract price, in which event the procuring entity concerned may rescind the contract.

Is a written order issued to by DPWH Project Engineer to suspend the contract work wholly or partly for such period?

Issued instead of Work Suspension Order if suspension / unworkable days is due to unfavorable weather condition (Rainy), weather disturbances or its effect (river swelling, storm surge, etc.), or other conditions rendering the site unworkable occur intermittently.

Is a written order issued by the DPWH Project Engineer to the contractor to resume construction operation covered by a previous Work Suspension Order, after the cause of or reason for the work suspension has been resolved.

Is a written authority issued by DPWH Project Engineer granting the contractor additional time beyond the approved completion date in order to carry out remaining works or any additional works?

Who is the delegated authority for local project authorized to issue Work Suspension Order, Work Resumption Order and Contract Time Extension, including the determination of the inclusive period necessary with cumulative inclusive period up to 60 days?

Who is the delegated authority for local project authorized to issue Work Suspension Order, Work Resumption Order and Contract Time Extension, including the determination of the inclusive period necessary with cumulative inclusive period beyond 60 days?

Who is the delegated authority for central/ UPMO project authorized to issue Work Suspension Order, Work Resumption Order and Contract Time Extension, including the determination of the inclusive period necessary with cumulative inclusive period beyond 120 calendar days?

This is prepared once the project reaches an accomplishment of ninety five percent of the total contract amount in preparation for the final turnover of the project.

The Procuring Entity shall terminate for default a contract for goods if Supplier fails to deliver or perform at least how many percent of the contract price within the periods specified in the contract

Procuring Entity shall terminate for default a contract for Infrastructure Projects when any of the following conditions attend its implementation due to the Contractor’s fault and while the project is on-going, it has incurred negative slippage of how many percent or more in accordance with Presidential Decree 1870;

Procuring Entity shall terminate for default due to the Contractor’s fault and after the contract time has expired, it has incurred a negative slippage of blank percent or more.

What is the minimum average compressive strength for a non-load bearing Concrete Hollow Blocks (CHB)?

How many pieces of Concrete Hollow Blocks (CHB) per square meter are used in the Cost Estimation?

What is the cement sand ratio to achieve 500 psi Concrete Hollow Blocks?

What is the minimum corrugation overlap on roofing sheet installation?

What is the mix ratio by volume of the mortar used in the installation of CHB and Louver blocks?

What is the design standard width for tourism and farm to market road projects?

How many project billboards are installed for each road/bridge/flood control project?

What is the dimension of a DPWH project billboard?

Is the total estimated cost of the project which covers the Civil Works Cost, Engineering Supervision and Administrative Overhead, Road Right-of-Way Acquisition Cost, Construction Contingency, etc. Include information about the project location and limits, quantity and unit cost for each item of work, construction duration, funding source, equipment requirements, etc.

Is the total estimated agency estimate (direct cost, indirect cost and tax) for civil works contract of infrastructure projects, wherein it is the ceiling of award of contract for government locally-funded projects and reference for comparison of bid costs of contractors for both locally-funded and foreign-assisted projects.

Is the determination of reasonable unit cost of each item of work which reflects the breakdown showing the quantities of work items, unit prices of materials, equipment rental rates, labor rates and DPWH-prescribed indirect costs including taxes?

One-storey up to 5-storeys in height, I.e., from 3.00 m up to a maximum of 15.00 meters above established grade.

How many percent is shrinkage factor used for material cost estimation of Embankment from Common Borrow by Equipment?

On the preparation of detailed unit price analysis, allowance for waste and/or losses shall not exceed _____ % of the material's requirement.

How many percent is shrinkage factor used for material cost estimation of Gravel Bedding?

What is the minimum cement content per m3 on a class A concrete?

What is the minimum cement content per m3 on a class C concrete

What is the minimum cement content per m3 on a Lean Concrete (for manual mixing)?

What is the unit weight of a 10mm diameter RSB?

What is the nominal weight of 16mm diameter x 6m length RSB?

The authority to approve the termination of contract for the Regional Projects.

Welcome arc/overhead boundary marker shall be provided with minimum vertical clearance of ______?

For overhead utility and power lines crossing the roadway, vertical clearance shall not be less than _____ from roadway surface.

For overhead utility and power lines from surface of sidewalks, vertical clearance shall not be less than _____

Structure at the two ends of a bridge use for transferring the loads from the bridge superstructure to the foundation bed and giving lateral support to the embankment.

How many percent is the Roadway Cross Slope for a Portland Cement Concrete Pavement (PCCP)?

What is the minimum width of a road shoulder?

How many percent is the Shoulder Cross Slope for a Gravel Surfacing?

Gutters, Valleys, Flashings Hip and Ridge Roll shall be fabricated from ___ cold rolled plain galvanized iron sheets.?

Which of the following Gauge No. of Galvanized Iron Sheets is the thickest?

What is the minimum end lap of Pre-painted Metal Sheets for Roofing Application?

What is the minimum end laps of Pre-painted Metal Sheets for Walling Application?

What is the cement/sand ratio to achieve 1,000 psi of concrete spacer?

What is the duration on the removal of forms and shoring of suspended slab and beams?

What is the concrete proportion (cement: sand: gravel) for Footings, Beams and Columns?

What is the concrete proportion (cement: sand: gravel) for Floor, slabs and ramps?

What is the minimum distance of a school building from a cliff?

What is the minimum distance of a school building from a power line tower?

What is the height distance between the center of the outlet and the flooring surface?

What is the height distance between the center of the switch and the flooring surface?

Soil or earth material which has been deposited by running water.

A horizontal strip or shelf built into an embankment or cut, to break the continuity of an otherwise long slope

A structure under a road, railway or embankment, whether of single or multiple barrel construction, generally with a width of less than five (5.0) meters per opening measured between inside wall faces.

An alternative method of procurement of goods from the previous winning bidder, whenever there is a need to replenish goods procured under a contract previously awarded through competitive bidding. a) Repeat order

Particles that pass through a number 4 sieve (4.75mm) and retained on a number 200 sieve (0.075mm).

What is the longitudinal grade for roads?

What is the maximum permissible variation in actual weight of a steel bar from the theoretical weight?

What is the maximum permissible variation in actual weight of a steel bar from the theoretical weight?

What is the rate of application of a curing compound on Portland Cement Concrete Pavement (PCCP)?

Concrete on area represented by cores will be considered adequate if the average strength of the cores is equal to at least 85%, and no single core is less than ____ of the specimen strength. a) 85%

The criteria for foundation of a school building for the actual soil bearing capacity on natural ground is ____ at depth of 1.5 m. Less than this value is subject for a changed in foundation.

For pavement design purpose, the varying axle loads are converted to a common denominator which is in terms of…

The minimum pavement width of carriageway for a national road shall be _____?

What is the prescribed concrete structure for a bridge with span of 13-20 meters