Piston 2 - Week 5A

What would be the result of ice formation in the induction system? -1
The mixture going lean
Reduction of engine power
Automatic activation of the wastegate actuator
The mixture going rich
Which of the following are parts of induction system for a normally aspirated aircraft engine? #2
The waste gate actuator
The turbine
The waste gate
The inlet ducting
Which of the following are parts of induction system for a normally aspirated aircraft engine? #4
The Carb heat box
The waste gate
The turbine
The waste gate actuator
What would be the result of ice formation in the induction system? -2
Rough running of the engine
The mixture going lean
The mixture going rich
Automatic activation of the wastegate actuator
What is the purpose of alternate air?
To pass warm air through carburetor to prevent ice formation in the induction system, or to melt ice that has formed.
To heat the air after it passes through the carburetor to prevent ice formation in the induction system
To pass warm air around carburetor to prevent ice formation in the induction system, or to melt ice that has formed.
To provide an second air path into the engine in case the air filter is plugged
Where does carburetor ice form?
Inside the scoop or on the filter
On the back side of the throttle valve
In the induction tubes
In the venturi
What is the purpose of carburetor heat?
To pass warm air around carburetor to prevent ice formation in the induction system, or to melt ice that has formed.
To pass warm air through carburetor to prevent ice formation in the induction system, or to melt ice that has formed.
To provide an second air path into the engine in case the air filter is plugged
To heat the air after it passes through the carburetor to prevent ice formation in the induction system
Which of the following are parts of induction system for a normally aspirated aircraft engine? #7
The turbine
The intake pipes
The waste gate actuator
The waste gate
Which of the following are parts of induction system for a normally aspirated aircraft engine? #3
The turbine
The air filter
The waste gate
The waste gate actuator
Which of the following are parts of induction system for a normally aspirated aircraft engine?
Air scoop, air filter, carburetor heat box, carburetor, intake manifold and intake pipes
Air scoop, inlet ducting, air filter, carburetor heat box, carburetor and intake pipes
Air scoop, inlet ducting, air filter, carburetor heat box, carburetor, intake manifold and intake pipes
Air scoop, inlet ducting, fuel filter, carburetor heat box, carburetor, intake manifold and intake pipes
What would be the result of ice formation in the induction system? -3
The mixture going lean
The mixture going rich
Greater engine power output
Possible engine failure
Where does impact ice form?
In the induction tubes
On the back side of the throttle valve
Inside the scoop or on the filter
In the venturi
Which of the following are parts of induction system for a normally aspirated aircraft engine? #5
The waste gate
The turbine
The waste gate actuator
The carburetor
Which of the following are parts of induction system for a normally aspirated aircraft engine? #6
The waste gate actuator
The turbine
The manifold
The waste gate
Where does throttle ice form?
In the venturi
On the back side of the throttle valve
In the induction tubes
Inside the scoop or on the filter
Which of the following are parts of induction system for a normally aspirated aircraft engine? #1
The turbine
The air scoop
The waste gate actuator
The waste gate
Which of the following is a secondary use for CAT? #2
Monitoring of cylinder temperatures
Monitoring of turbine temperatures
Monitoring of backfiring
Monitoring of combustion efficiency
Which of the following is a secondary use for CAT? #3
Monitoring of turbine temperatures
Monitoring for induction system fires
Monitoring of combustion efficiency
Monitoring of cylinder temperatures
Which instrument would be used to send air temperature going into the carburetor?
An OAT gauge
A TIT gauge
A BAT gauge
A CAT gauge
What will a few aircraft use to tell the crew of ice formation in the carburetor?
Pilot awareness of icing conditions
An ice light shining in instrument panel
An ice thickness gauge
An ice light shining on the wing
Where will carburetor heat get its warm air from? #1
From unfiltered air passing through an electric heater
From filtered air passing through a heat muff
From unfiltered air passing through a heat muff
From filtered air passing through an electric heater
Which of the following is a secondary use for CAT? #1
Monitoring of turbine temperatures
Monitoring of combustion efficiency
Monitoring of cylinder temperatures
Monitoring of charge density
Where will carburetor heat get its warm air from? #2
From unfiltered air passing through a shroud heater
From filtered air passing through an electric heater
From filtered air passing through a shroud heater
From unfiltered air passing through an electric heater
What do most aircraft use to tell the crew of ice formation in the carburetor?
An ice light shining on the wing
An ice thickness gauge
An ice light shining in instrument panel
Pilot awareness of icing conditions
Which of the following is a type of air filter on an aircraft engine? #2
HEPA & oil air filter
Natural sponge & oil air filter
Polyurethane foam & glycol air filter
Fiberglass air filter
What is the typical life of a paper air filter?
100 hrs or on condition
100hrs or annual
500 hrs or on condition
1yr
What is the typical life of a foamr air filter?
500 hrs or on condition
100 hrs or on condition
1yr
100hrs or annual
Which of the following is a type of air filter on an aircraft engine? #1
Paper air filter
HEPA air filter
Natural sponge & oil air filter
Fiberglass air filter
On a paper air filter what would you inspect the housing and seal for?
Freedom of movement & cracks, proper hardware
Chafing and wear, proper hardware
Cracking, proper hardware & security
Cleanliness and colour, proper hardware
When inspecting a paper air filter how would you find pin holes?
Look closely with compressed air blowing on the back side
Look closely with a light on the back side
By looking at how dust/dirt have built up on the filter
By looking at the colour of the filter
When inspecting a paper air filter what are you looking for?
Pin holes & tears
Pea sized holes and cracks
Filter flexibility
Glycol colour and wetness
How will a paper air filter be cleaned?
Tap the filter (front side down) and low pressure blow clean from the back
Tap the filter (front side up) and low pressure blow clean from the front
Tap the filter (front side up) and high pressure blow clean from the front
Tap the filter (front side down) and high pressure blow clean from the back
On a paper air filter what would you inspect the housing and seal for?
Chafing and wear
Freedom of movement & cracks
Cleanliness and colour
Condition & security
Which of the following is a type of intake manifold? #2
Cross draft
Downdraft
Biploar draft
Reverse draft
On which side of the engine would an downdraft type induction system be installed?
Behind
On the top
On the bottom
In the front
Why do Lycoming engines have the intake manifold inside the sump? #1
To cool the mixture slightly and improve vaporization
To heat the mixture slightly and improve vaporization
To heat the air slightly and reduce its density
To cool the air slightly and increase its density
What is used to secure the rubber couplings in the induction system?
Studs & lock washers
Studs & lock nuts
Nuts & bolts
Clamps
Where would the intake manifold be on a Lycoming engine?
In the oil sump
Below the engine
Behind the engine
Above the engine
What would be used to equalize the induction pressures on both sides of the engine? #1
Differential turbo control
Balance tubes
Differential wastegate control
Ground adjustable orifices
On which side of the engine would an updraft type induction system be installed?
On the top
On the bottom
In the front
Behind
What is used to connect different sections of the intake manifold?
Gaskets
Ball joints
Slip joints
Rubber couplings
Which of the following is a type of intake manifold? #1
Updraft
Reverse draft
Cross draft
Biploar draft
What would be used to equalize the induction pressures on both sides of the engine? #2
Differential wastegate control
Differential turbo control
Ground adjustable orifices
Cross over tubes
Why do Lycoming engines have the intake manifold inside the sump? #2
To cool the air slightly
To cool the oil slightly
To heat the air slightly
To cool the mixture slightly
{"name":"Piston 2 - Week 5A", "url":"https://www.quiz-maker.com/QPREVIEW","txt":"What would be the result of ice formation in the induction system? -1, Which of the following are parts of induction system for a normally aspirated aircraft engine? #2, Which of the following are parts of induction system for a normally aspirated aircraft engine? #4","img":"https://www.quiz-maker.com/3012/images/ogquiz.png"}
Powered by: Quiz Maker