Engineering Graphics Quiz
Designation:
1.The primary unit of measurement for engineering drawings and design in the mechanical industries is the:
A) Millimeter
B) Centimeter
C) Meter
D) Kilometer
2.The eccentricity of which of the following curve is greater than one?
A) Ellipse
B) Hyperbola
C) Parabola
D) None of these
3.For drawing of small instruments, watches etc. The scale used is:
A) Reduced scale
B) Full scale
C) Enlarged scale
D) None of these
4.In the first angle projection method, the view seen from left is placed on
A) Above Front View
B) Right of Front View
C) Above Top View
D) Below Front View
5.In the game of cricket, a ball is thrown from the boundary and reaches the gloves of the wicket keeper, the curve traced out will be
A) Hyperbola
B) Involute
C) Parabola
D) Cycloid
6.If the object lies in third quadrant, its position with respect to reference planes will be
A) In front of VP, Above HP
B) Behind VP, Above HP
C) Behind VP, Below HP
D) In front of VP, Below HP
7.When the front view of line having a length less than the original length then which of the following is correct?
A) Line is inclined to H.P.
B) Line is inclined to V.P.
C) Line is inclined to both H.P. and V.P
D) Line is inclined to V.P. and Line is inclined to both H.P. and V.P.
8.Name the solid formed by four equilateral triangle
A) Square pyramid
B) Triangular pyramid
C) Tetrahedron
D) Square prism
9.When the axis of the solid is parallel to both HP and VP the view which reveals the true shape of the base is
A) Front view
B) Top view
C) Side view
D) None of these
10.A cylinder standing on the HP is cut by a vertical plane parallel to the axis and away from it. The shape of the section will be
A) Rectangle
B) Circle
C) Ellipse
D) Hyperbola
11.The preferred size of the drawing sheets is recommended by the ______
A) BIS
B) ASME
C) ASTM
D) NIST
12. Match the following.
A) 1, I; 2, ii; 3, iii; 4, iv
B) 1, ii; 2, iii; 3, iv; 4, I
C) 1, ii; 2, iv; 3, iii; 4, I
D) 1, iv; 2, iii; 3, ii; 4, I
13.'Representative fraction’ (RF) is defined as
A)Length of an object in the drawing / Actual length of the object
B)Length of an object in the drawing / Isometric length of the object
C)Actual length of the object / Length of an object in the drawing
D)Isometric length of the object / Length of an object in the drawing
14.The side view of an object is drawn in
A)Vertical plane
B)Horizontal plane
C)Profile plane
D)Any of the above
15.The following are the Polyhedron except
A)Prism
B)Pyramid
C)Cube
D)Cylinder
16.If a solid is cut by a cutting plane parallel to the base of the solid and top part is removed, the remaining part is called
A)Frustum of a solid
B)Truncated solid
C)Oblique solid
D)None of the above
17.A right circular cone resting on HP on its base is cut by a section plane parallel to HP, bisecting its axis. The true shape of the section is
A)Parabola
B)Hyperbola
C)Ellipse
D)Circle
18.Development of surfaces is used in the development of
A)Piping
B)Air conditioning duct
C)Buckets
D)All of the above
19.The development of lateral surfaces of a pentagonal pyramid is
A)Five squares
B)Five Rectangles
C)Five triangles
D)None of the above
20.The isometric projection of a circle is a
A)Circle
B)Ellipse
C)Hyperbola
D)Parabola
21.When a solid completely penetrates another solid, there will be two lines of intersection. These lines are called ______
A) line of interpenetration
B) concyclic curves of lines
C) hidden lines
D) inside line
22.Identify the side view of the below given component.
0%
0
0%
0
0%
0
0%
0
23.Identify the front view of the below given component.
0%
0
0%
0
0%
0
0%
0
24.The development of the curved surface of a cone is a _______ of a _______
A) sector, circle
B) segment, circle
C) segment, ellipse
D) arc, parabola
25. A pentagon is placed perpendicular to horizontal plane and inclined to profile plane which of the following is true.
A)Front view-line, top view- pentagon
B) Front view- pentagon, top view- line
C) Front view –line, top view-line
D) Top view-line, side view- line
{"name":"Engineering Graphics Quiz", "url":"https://www.quiz-maker.com/QPREVIEW","txt":"Full Name:, Designation:, Department:","img":"https://www.quiz-maker.com/3012/images/ogquiz.png"}
More Quizzes
FSG#FSG2019_DONE 21.01.2021
11620
Pokemon Starters
1169
Do you know your wife? ;)
1059
Dumplings
12617
Supply Chain - Free Global Management Practice
15816795
SSAT Synonyms - Free Vocabulary Practice
201021607
Michigan Accent Test - Do You Know the Local Slang?
201016564
Hairdressing Exam Practice with Answers - Free
201017159
Pokemon Girlfriend - Find Your Perfect Match
201017614
Emotional Intelligence - Test Your EQ with Answers
201018713
Business Proposal - Which Character Are You?
201018874
VTM Clan: Find Your Vampire: The Masquerade Clan
201017286