Rulebook Test

Create an image of a racing car pit stop with team members discussing technical specifications and reviewing a rulebook, in a dynamic and engaging atmosphere.

CGMR Rulebook Challenge

Test your knowledge of the CGMR Rulebook with our engaging quiz designed for enthusiasts and participants alike. This quiz will cover essential regulations and specifications that every team member should be familiar with.

Challenge yourself with questions like:

  • Penalty deductions for late corrections
  • Specifications for steel tubing
  • Requirements for the shutdown circuit
15 Questions4 MinutesCreated by InspectingEagle47
Late correction submission for CGMR: Points penalty per 24h & Penalty deducted from ?
10, Overall
5, ED
5, Overall
10, ED
Steel tubing has to be made from unalloyed carbon steel with a maximum content of ______ carbon, ______ manganese and _______ of any other element.
0.6%, 1.7%, 0.3%
0.3%, 1.7%, 0.6%
1.7%, 0.6%, 0.3%
None of the above
If the front hoop is inclined more than 10° to the rear, additional braces extending rearwards are required.
True
False
Which of the following is TRUE.
The attachment of the IA assembly to a monocoque structure requires an approved “Structural Equivalency Spreadsheet” per T3.6 that shows equivalency to a minimum of four 8 mm metric grade 8.8 bolts.
LV batteries must be protected from short circuits, more than 100 mm from ungrounded terminals.
The costs of hand or power tools must be included.
An OC occurs when the vehicle has all four wheels outside the course boundary as indicated by edge marking.
Hand held fire extinguishers are not permitted to be mounted on or in the vehicle.
True
False
The fuel tank must be located within the surface envelope (see T1.1.15), except the fuel filler neck if it is _______ above the ground.
350m
35 mm
35cm
None of the above
The brake light must meet the following requirements:
If a single line of LEDs is used, the maximum length is 150 mm.
Maximum shining surface of 15 cm2 with even luminous intensity.
Rectangular, triangular or near circular shape.
When LED lights are used without a diffuser, they may not be more than 20 mm apart.
Which of the following is FALSE.
Catch cans must be rigidly mounted to the chassis and located rearwards of the firewall below the driver’s shoulder level.
Adjustable tie-rod ends must be constrained with a jam nut to prevent loosening.
At least three separate sensors must be used as APPSs. Separate is defined as not sharing supply or signal lines.
T-shirts, socks or other undergarments made from nylon or any other synthetic material which will melt when exposed to high heat are prohibited.
This inspection responsible person must be:
Familiar with the vehicle.
Able to show compliance of the vehicle with all points mentioned on the technical inspection sheet.
Able to perform the technical inspection autonomously observed by the officials, when asked.
All of these.
The shutdown circuit directly controls all electrical power to the ignition, fuel injectors and all fuel pumps. It must act through a minimum of three mechanical relays. One relay for the fuel pump and at least two relay for injection and ignition.
True
False
Business plan presentation scoring: Demonstration and Structure
10
15
20
5
When the operating condition is damp, teams may change between dry tires and wet tires:
Any time during the acceleration, skidpad, and Brake test.
Any time before taking the green flag to start endurance.
Both A&B
None
Only three team members excluding the driver may enter the driver change area. They may only bring the tools required to adjust the vehicle to accommodate the second driver and/or change tires.
True
False
Missed Presentation Session with less than 48 hour notice:
10 Points
25 Points
5 Points
None of the above
Wheel lug bolts and studs must be made of aluminum or titanium.
True
False
{"name":"Rulebook Test", "url":"https://www.quiz-maker.com/QPREVIEW","txt":"Test your knowledge of the CGMR Rulebook with our engaging quiz designed for enthusiasts and participants alike. This quiz will cover essential regulations and specifications that every team member should be familiar with.Challenge yourself with questions like:Penalty deductions for late correctionsSpecifications for steel tubingRequirements for the shutdown circuit","img":"https://cdn.poll-maker.com/104-5108842/img-9uukj9ciz15y9dsdatcoez7y.jpg"}
Powered by: Quiz Maker