Qz05

A PC is to access a web server on another network. Which inter-VLAN method will provide the highest bandwidth at Layer 3 and also provide a default gateway for the PC?
router on a stick
Multilayer switch with routing enabled
trunked interface between the router and the switch
multiple physical interfaces on the router, all connected to a Layer 2 switch
The gig0/0 interface does not support inter-VLAN routing.
The no shutdown command has not been configured.
The IP address on CiscoVille is incorrect.
The encapsulation dot1Q 20 command has not been configured.​
Which two errors can be identified from the show running-config command output from the router? (Choose two.)
There is no IP address that is configured for the router physical interface.
The VLAN ID for VLAN 30 is wrongly configured.​
A command to configure the router physical interface as a trunk is missing.
The IP address and subnet mask are wrongly configured for VLAN 20.​
The no shutdown command was not issued on subinterfaces.
Refer to the exhibit. Inter-VLAN communication between VLAN 10, VLAN 20, and VLAN 30 is not successful. What is the problem?​
The access interfaces do not have IP addresses and each should be configured with an IP address.
The FastEthernet0/2, FastEthernet0/3, and FastEthernet0/4 interfaces are configured as trunk.
The switch interface FastEthernet0/1 is configured to not negotiate and should be configured to negotiate.​
The switch interfaces FastEthernet0/2, FastEthernet0/3, and FastEthernet0/4 are configured to not negotiate and should be configured to negotiate.​
What is the meaning of the number 10 in the encapsulation dot1Q 10 native router subinterface command?​
the interface number
the subinterface number​
the subnet number
the VLAN ID
A network administrator enters the following command sequence on a Cisco 3560 switch. What is the purpose of these commands? Switch(config)# interface gigabitethernet 0/1 Switch(config-if)# no switchport
to shut down the Gi0/1 port
to make the Gi0/1 port a routed port
to enable the Gi0/1 port as a switch virtual interface
to enable the Gi0/1 port as a bridge virtual interface
Refer to the exhibit. A network administrator has configured router CiscoVille with the above commands to provide inter-VLAN routing. What type of port will be required on a switch that is connected to Gi0/0 on router CiscoVille to allow inter-VLAN routing?
routed port
access port
trunk port
SVI
Which option should be used after the sdm prefer configuration command to enable static routing on Cisco Catalyst 2960 switches?
Switch(config)# sdm prefer qos
Switch(config)# sdm prefer default
Switch(config)# sdm prefer lanbase-routing
Switch(config)# sdm prefer dual-ipv4-and-ipv6
Which scalable method must be implemented in order to provide inter-VLAN routing on a switched network with more than 1000 VLANs?
configuring static routes on a Layer 2 switch device
routing traffic internally to a Layer 3 switch device
connecting each physical router interface to a different physical switch port, with each switch port assigned to a different VLAN
Connecting a router interface to a switch port that is configured in trunk mode to route packets between VLANs, with each VLAN assigned to a router subinterface​
Refer to the exhibit. Which implementation of inter-VLAN routing does this topology use?
interdomain
router on a stick
Multiple physical interfaces
routing via a multilayer switch
Fill in the blank. Do not use abbreviated commands. The switchport parameter can be added to the show interfaces interface_id command to display the administrative and operational switch interface mode.​
{"name":"Qz05", "url":"https://www.quiz-maker.com/QPREVIEW","txt":"A PC is to access a web server on another network. Which inter-VLAN method will provide the highest bandwidth at Layer 3 and also provide a default gateway for the PC?, Which two errors can be identified from the show running-config command output from the router? (Choose two.)","img":"https://cdn.poll-maker.com/11-495619/qz0501.png?sz=1200"}
Powered by: Quiz Maker