CCNA 2 Final Exam
CCNA 2 Final Exam Preparation Quiz
Test your knowledge and enhance your understanding of fundamental networking concepts with our CCNA 2 Final Exam Preparation Quiz. Designed for networking students and professionals alike, this quiz consists of 65 questions covering a range of topics including routing protocols, VLANs, and network security.
Participate in the quiz to:
- Solidify your networking knowledge
- Prepare for the CCNA certification exam
- Get instant feedback on your performance
Refer to the exhibit. Assuming that the routing tables are up to date and no ARP messages are needed, after a packet leaves H1, how many times is the L2 header rewritten to the path to H2?
1
2
3
3
4
5
6
Refer to the exhibit. Which highlighted value represents a specific destination network in the routing table?
0.0.0.0
172.16.100.64
172.16.100.2
110
791
Which type of static route is configured with a greater administrative distance to provide a backup route to a route learned from a dynamic routing protocol?
Standard static route
Floating static route
Default static route
Summary static route
Refer to the exhibit. Which route was configured as a static route to a specific network using the next-hop address?
C 172.16.2.0/24 is directly connected, Serial0/0/0
S 192.168.2.0/24 [1/0] via 172.16.2.2
S 192.168.2.0/24 is directly connected, Serial0/0/0
S 0.0.0.0/0 [1/0] via 172.16.2.2
What network prefix and prefix-length combination is used to create a default static route that will match any IPv6 destination?
::/128
::/0
::1/64
FFFF::/128
A router has used the OSPF protocol to learn a route to the 172.16.32.0/19 network. Which command will implement a backup floating static route to this network?
Ip route 172.16.32.0 255.255.224.0 S0/0/0 200
Ip route 182.16.0.0 255.255.240.0 S0/0/0 200
Ip route 172.16.0.0 255.255.224.0 S0/0/0 100
Ip route 172.16.32.0 255.255.0.0 S0/0/0 100
Refer to the exhibit. Currently router R1 uses an EIGRP route learned from Branch2 to reach the 10.10.0.0/16 network. Which floating static route would create a backup route to the 10.10.0.0/16 network in the event that the link between R1 and Branch2 goes down?
Ip route 10.10.0.0 255.255.0.0 Serial 0/0/0 100
Ip route 10.10.0.0 255.255.0.0 209.165.200.226 100
Ip route 10.10.0.0 255.255.0.0 209.165.200.225 50
Ip route 10.10.0.0 255.255.0.0 209.165.200.225 100
Which statement describes a route that has been learned dynamically?
It is automatically updated and maintained by routing protocols
It is unaffected by changes in the topology of the network
It has an administrative distance of 1
It is identified by the prefix C in the routing table
Compared with dynamic routes, what are two advantages of using static routes on a router (choose two)?
They use fewer resources
They improve the efficiency of discovering neighboring networks
They take less time to converge when the network topology changes
They improve network security
They automatically switch the path to the destination network when the topology changes
A network administrator adds the default-information originate command to the configuration of a router that uses RIP as the routing protocol. What will result from adding this command?
The router will be reset to the default factory information
The router will not forward routing information that is learned from other routers
The router will propagate a static default route in its RIP updates, if one is present
The router will only forward packets that originate on directly connected networks
Refer to the exhibit. What is the administrative distance value that indicates the route for R2 to reach the 10.10.0.0/16 network?
1
0
90
20512256
A network administrator reviews the routing table on the router and sees a route to the destination network 172.16.64.0/18 with a next-hop IP address of 192.168.1.1. What are two descriptions of this route? (Choose two)
Default route
Supernet route
Ultimate route
Parent route
Level 2 child route
Which two factors are important when deciding which interior gateway routing protocol to use (choose two)?
Scalability
ISP selection
Speed of convergence
The autonomous system that is used
Campus backbone architecture
Employees of a company connect their wireless laptop computers to the enterprise LAN via wireless access points that are cabled to the Ethernet ports of switches. At which layer of the three-layer hierachical network design model do these switches operate?
Distribution
Data link
Physical
Access
Core
What is a characteristic of the distribution layer in the three layer hierachical model?
Acts as the backbone for the network aggregating and distributing network traffic throughout the campus
Provides access to the rest of the network through switching, routing, and network access policies
Distributes access to end users
Represents the network edge
Which information does a switch use to populate the MAC address table?
The destination MAC address and the incoming port
The destination MAC address and the outgoing port
The source and destination MAC address and the incoming port
The source and destination MAC address and the outgoing port
The source MAC address and the incoming port
The source MAC address and the outgoing port
Which statement is correct about Ethernet switch frame forwarding decisions?
Frame forwarding decisions are based on MAC address and port mappings in the CAM table
Cut-through frame forwarding ensures that invalid frames are always dropped
Only frames with a broadcast destination address are forwarded out all active switch ports
Unicast frames are always forwarded regardless of the destination MAC address
Which switching method drops frames that fail the FCS check?
Borderless switching
Cut-through switching
Ingress port buffering
Store-and-forward switching
In what situation would a Layer 2 swtich have an IP address configured?
When the Layer 2 switch needs to forward user traffic to another device
When the Layer 2 switch is the default gateway of user traffic
When the Layer 2 switch needs to be remotely managed
When the Layer 2 switch is using a routed port
A network administrator is configuring a new Cisco switch for remote management access. Which three items must be configured on the switch for the task (choose three)?
IP adress
VTP domain
Vty lines
Default VLAN
Default gateway
Loopback address
A network technician has been asked to secure all switches in the campus network. The security requirements are for each switch to automatically learn and add MAC addresses to both the address table and the running configuration. Which port security configuration will meet these requirements?
Auto secure MAC addresses
Dynamic secure MAC addresses
Static secure MAC addresses
Sticky secure MAC addresses
A network administrator is configuring port security on a Cisco switch . When a violation occurs, which violation mode that is configured on an interface will cause packets with an unknown source address to be dropped with no notification sent?
Off
Restrict
Protect
Shutdown
Two employees in the Sales department work different shifts with their laptop computers and share the same Ethernet port in the office. Which set of commands would allow only these two laptops to use the Ethernet port and create violation log entry without shutting down the port if a violation occurs?
Switchport mode access ; switchport port-security
Switchport mode access ; switchport port-security ; switchport port-security maximum 2 ; switchport port-security mac-address-sticky ; switchport port-secuirty violation restrict
Switchport mode access ; switchport port-security maximum 2 ; switchport port-security mac-address sticky
Switchport mode access ; switchport port-security maximum 2 ; switchport port-security mac-address sticky ; switchport port-security violation protect
Refer to the exhibit. What protocol should be configured on SW-A Port 0/1 if it is to send traffic from multiple VLANs to switch SW-B?
Spanning Tree
RIP v2
IEEE 802.11Q
ARP
Rapid Spanning Tree
A Cisco Catalyst switch has been added to support the use of multiple VLANs as part of an enterprise network. The network technician finds it necessary to clear all VLAN information from the switch in order to incorporate a new network design. What should the technician do to accomplish this task?
Erase the startup configuration and reboot the switch
Erase the running configuration and reboot the switch
Delete the startup configuration and the vlan.dat in the flash memory of the switch and reboot the switch
Delete the IP address that is assigned to the management VLAN and reboot the switch
What VLANs are allowed across a trunk when the rang of allowed VLANs is set to the default value?
All VLANs will be allowed across the trunk
Only VLAN 1 will be allowed across the trunk
Only the native VLAN will be allowed across the trunk
The switches will negotiate via VTP which VLANs to allow across the trunk
Refer to the exhibit. A network administrator is configuring inter VLAN routing on a network. For now, only one VLAN is bein used, but more will be added soon. What is the missing parameter that is show as the highlighted question mark in the graphic?
It identifies the subinterface
It identifies the VLAN number
It identifies the native VLAN number
It identifies the encapsulation that is used
It identifies the number of hosts that are allowed on the interface
A network administrator is designing an ACL. The networks 192.168.1.0/25, 192.168.0.0/25, 192.168.1.128/26, and 192.168.1.192/26 are affected by the ACL. Which wildcard mask, if any, is the most efficient to use when specifying all of these networks in a single ACL permit entry?
0.0.0.127
0.0.0.255
0.0.1.255
0.0.255.255
A single ACL command and wildcard mask should not be used to specify these particular networks or other traffic will be permitted or denied and present security risk
The computers used by the network administrators for a school are on the 10.7.0.0/27 network. Which two commands are needed at a minimum to apply an ACL that will ensure that only devices that are used by the network administrators will be allowed Telnet access to the routers (choose two)?
Access-class 5 in
Access-list 5 deny andy
Access-list standard VTY ; permit 10.7.0.0 0.0.0.127
Access-list 5 permit 10.7.0.0 0.0.0.31
Ip access-group 5 out
Ip access-group 5 in
A network engineer has created a standard ACL to control SSH access to a router. Which command will apply the ACL to the VTY lines?
Access-group 11 in
Access-class 11 in
Access-list 11 in
Access-list 110 in
What is the reason why the DHCPREQUEST message is sent as a broadcast during the DHCPv4 process?
To notify other DHCP servers on the subnet that the IP address was leased
To notify other hosts not to request the same IP address
For hosts on other subnets to receive the information
For routers to fill their routing tables with this new information
Which set of commands will configure a router as a DHCP server that will assign IPv4 addresses to the 192.168.100.0/23 LAN while reserving the first 10 and the last addresses for static assignment?
Ip dhcp excluded-address 192.168.100.1 192.168.100.10 ; ip dhcp excluded-address 192.168.100.254 ; ip dhcp pool LAN-POOL-100 ; network 192.168.100.0 255.255.255.0 ; ip default-gateway 192.168.100.1
Ip dhcp excluded-address 192.168.100.1 192.168.100.10 ; ip dhcp excluded-address 192.168.101.254 ; ip dhcp pool LAN-POOL-100 ; network 192.168.100.0 255.255.254.0 ; default-router 192.168.100.1
Dhcp pool LAN-POOL-100 ; ip dhcp excluded-address 192.168.100.1 192.168.100.9 ; ip dhcp excluded-address 192.168.100.254 ; network 192.168.100.0 255.255.254.0 ; default-router 192.168.101.1
Ip dhcp excluded-address 192.168.100.1 192.168.100.9 ; ip dhcp excluded-address 192.168.101.254 ; ip dhcp pool LAN-POOL-100 ; ip network 192.168.100.0 255.255.254.0 ; ip default-gateway 192.168.100.1
Which command, when issued in the interface configuration mode of a router, enables the interface to acquire an IPv4 address automatically from an ISP, when that link to the ISP is enabled?
Ip dhcp pool
Ip address dhcp
Service dhcp
Ip helper-address
Refer to the exhibit. A network administrator is configuring a router as a DHCPv6 server. The administrator issues a show ipv6 dhcp pool command to verify the configuration. Which statement explains the reason that the number of active clients is 0?
The default gateway address is not provided in the pool
No clients have communicated with the DHCPv6 server yet
The IPV6 DHCP pool configuration has no IPv6 address range specified
The state is not maintained by the DHCPv6 server under stateless DHCPv6 operation
Refer to the exhibit. Which statement shown in the output allows router R1 to respond to stateless DHCPv6 requests?
Ipv6 unicast-routing
Dns-server 2001:DB8:8::8
Ipv6 dhcp server LAN1
Ipv6 nd other-config-flag
Prefex-delegation 2001:DB8:8::/48 00030001000E84244E70
Refer to the exhibit. NAT is configured on Remote and Main. The PC is sending a request to the web server. What IPv4 address is the source IP address in the packet between Main and the web server?
10.130.5.76
209.165.200.245
203.0.113.5
172.16.1.10
192.0.2.1
209.165.200.226
Refer to the exhibit. Which two statements are correct based on the output as shown in the exhibit (choose two)?
The output is the result of the show ip nat translations command
The host with the address 209.165.200.235 will respond to requests by using a source address of 192.168.10.10
The host with the address 209.165.200.235 will respond to requests by using a source address of 209.165.200.235
Traffic with the destination address of a public web server will be sourced from the IP of 192.168.1.10
The output is the result of the show ip nat statistics command
Refer to the exhibit. A network administrator has configured R2 for PAT. Why is the configuration incorrect?
The static NAT entry is missing
NAT-POOL2 is bound to the wrong ACL
The ACL does not define the list of addresses to be translated
The overload keyword should not have been applied
A college marketing department has a networked storage device that uses the IP address 10.18.7.5, TCP port 443 for encryption, and UDP port 4365 for video streaming. The college already uses PAT on the router that connects to the Internet. The router interface has the public IP address of 209.165.200.225/30. The IP NAT pool currently uses the IP addresses ranging from 209.165.200.225-236. Which configuration would the network administrator add to allow this device to be accessed by the marketing personnel from home?
Ip nat pool mktv 10.18.7.5 10.18.7.5
Ip nat outside source static 10.18.7.5 209.165.200.225
Ip nat inside source static tcp 10.18.7.5 443 209.165.200.225 443 ; ip nat inside source udp 10.18.7.5 4365 209.165.200.225 4365
Ip nat inside source static tcp 209.165.200.225 443 10.18.7.5 443 ; ip nat inside source static udp 209.165.200.225 4365 10.18.7.5 4365
No additional configuration necessary
Refer to the exhibit. Based on the output that is show, what type of NAT has been implemented?
Dynamic NAT with a pool of two public IP addresses
PAT using an external interface
Static NAT with one entry
Static NAT with a NAT pool
Refer to the exhibit. An administrator is trying to configure PAT on R1, but PC-A is unable to access the Internet. The administrator tries to ping a server on the Internet from PC-A and collects the debugs that are shown in the exhibit. Based on this output, what is most likely the cause of the problem?
The address of Fa0/0 should be 64.100.0.1
The NAT source access list matches the wrong address range
The inside global address is not on the same subnet as the ISP
The inside and outside NAT interface have been configured backwards
A network engineer is interested in obtaining specific information relevant to the operation of both distribution and access layer Cisco devices. Which command provides common information relevant to both types of devices?
Show ip protocols
Show ip interface
Show cdp neighbors
Show port-security
Show mac-address-table
Which two statements are correct if a configured NTP master on a network cannot reach any clock with a lower stratum number (choose two)?
The NTP master will claim to be synchronized at the configured stratum number
The NTP master wil be the clock with 1 as its stratum number
An NTP server with a higher stratum number will become the master
Other systems will be willing to synchronize to that master using NTP
The NTP master will lower its stratum number
What are three functions provided by the syslog service (choose three)?
To gather logging information for monitoring and troubleshooting
To select the type of logging information that is captured
To specify the destinations of captured messages
To periodically poll agents for data
To provide statistics on packets that are flowing through a Cisco device
To provide traffic analysis
Refer to the exhibit. An administrator is examining the message in a syslog server. What can be determined from the message?
This is a notification message for a normal but significant condition
This is an alert message for which immediate action is needed
This is an error message for which warning conditions exist
This is an error message that indicates the system is unusable
When a customer purchases a Cisco IOS 15.0 software package, what serves as the receipt for that customer and is used to obtain the license as well?
Software Claim Certificate
End User License Agreement
Unique Device Identifier
Product Activation Key
Refer to the exhibit. The network administrator enters these commands into the R1 router: >> R1# copy running-config tftp ; Address or name of remote host []? << When the router prompts for an address of remote host name, what IP address should the administrator enter at the prompt?
192.168.9.254
192.168.10.1
192.168.10.2
192.168.11.252
192.168.11.254
Match the router memory type that provides the primary storage for the router feature (Not all options are used).
Console access
Flash
NVRAM
RAM
ROM
Nothing
Full operating system
Flash
NVRAM
RAM
ROM
Nothing
Limited operating system
Flash
NVRAM
RAM
ROM
Nothing
Routing table
Flash
NVRAM
RAM
ROM
Nothing
Startup configuration file
Flash
NVRAM
RAM
ROM
Nothing
Match each borderless switched network principle to its description (Not all options are used).
Match each borderless switched network principle to its description (Not all options are used).
Layers minimize the number of devices on any one tier that share a single point of failure.
Resiliency
Hierachical
Modularity
Flexibility
None
Each layer has specific roles and functions that can scale easily.
Resiliency
Hierachical
Modularity
Flexibility
None
This provides "always-on" dependability.
Resiliency
Hierachical
Modularity
Flexibility
None
This provides quality of service and additional security
Resiliency
Hierachical
Modularity
Flexibility
None
This shares the network traffic load across all network resources
Resiliency
Hierachical
Modularity
Flexibility
None
Match the description to the correct VLAN type (Not all options are used).
Match the description to the correct VLAN type (Not all options are used).
Configured to carry user generated traffic
Default VLAN
Management VLAN
Data VLANs
Native VLAN
None
All switch ports are assigned to this VLAN after initial bootup of the switch
Default VLAN
Management VLAN
Data VLANs
Native VLAN
None
Carries untagged traffic
Default VLAN
Management VLAN
Data VLANs
Native VLAN
None
An IP address and subnet mask are assigned to this VLAN, allowing the switch to be accessed by HTTP, Telnet, SSH, or SNMP
Default VLAN
Management VLAN
Data VLANs
Native VLAN
None
Only accessible by the network administrator
Default VLAN
Management VLAN
Data VLANs
Native VLAN
None
{"name":"CCNA 2 Final Exam", "url":"https://www.quiz-maker.com/QPREVIEW","txt":"Test your knowledge and enhance your understanding of fundamental networking concepts with our CCNA 2 Final Exam Preparation Quiz. Designed for networking students and professionals alike, this quiz consists of 65 questions covering a range of topics including routing protocols, VLANs, and network security.Participate in the quiz to:Solidify your networking knowledgePrepare for the CCNA certification examGet instant feedback on your performance","img":"https:/images/course8.png"}