Quiz 1
Engineering and Safety Quiz
Test your knowledge on important engineering principles, safety regulations, and practical applications in the field. This quiz covers topics such as fluid mechanics, structural integrity, and safety equipment for vehicles.
- 10 challenging questions
- Multiple choice and checkbox formats
- Ideal for students and professionals alike
The vertical component of the landing speed of a parachute must be inferior to 6 m/s. The total mass of the skydiver with parachute is of 120 kg. Considering the parachute as the inner surface of half a sphere, which is the minimal diameter of the open parachute?
6.6 m
14.4 m
7.0 m
7.2 m
3.3 m
8.2 m
3.5 m
Which of the following statements about the Front Bulkhead support is true?
The upper support member must be attached to the front bulkhead a maximum of 50 mm below the top-most surface of the front bulkhead, and attached to the front hoop a maximum of 50 mm below the upper side impact member. If the attachment point of the upper member ist greater than 100 mm above the upper side impact member , node-to-node triangulated bracing is required to transfer load to the side impact member.
The upper support member must be attached to the front bulkhead a maximum of 50 mm below the top-most surface of the front bulkhead, and attached to the front hoop a maximum of 50 mm below the upper side impact member. If the attachment point of the upper member is lower than 100 mm above the upper side impact member, node-to-node triangulated bracing is required to transfer load to the main hoop
The upper support member must be attached to the base of the front bulkhead and the base of the front hoop.
The upper support member must be attached to the front bulkhead a maximum of 50 mm below the top-most surface of the front bulkhead, and attached to the front hoop a maximum of 50 mm below the left side impact member. If the attachment point of the upper member is greater than 100 mm above the upper side impact member, node-to-node triangulated bracing is required to transfer load to the main hoop.
The lower support member must be attached to the base of the front bulkhead and the base of the side impact member.
The perimeter shear strength of the monocoque laminate in the front bulkhead support structure must be at least 4 kN
A rollercoaster car [mass m] runs down a slope before going through a lopp with a radius of R=6m. From which height doea a car have to start (with zero velocity) to stick to the track through the loop? Answer without any decimal in metres!
10 m
15 m
12 m
17 m
20 m
9 m
Which of the following illustrations from the rulebook is wrong?
0%
0
0%
0
0%
0
0%
0
0%
0
0%
0
On fluid mechanics, boundary is defined as the layer of fluid in the immediate vicinity of a bounding surface where the effects of viscosity are significant. On a boundary layer:
The flow is laminar
The Bernoulli equations do not apply
The flow is turbulent
The laws of momentum, energy and mass conservation do not apply
None
The Bernoulli equations apply
Regarding the Fire Extinguishers, it is correct to say that:
One extinguisher mus accompany the vehicle wherever the vehicle is moved, and the second must readily be available in the team's paddock area
Each team must have at least two dry chemical/ dry powder fire extinguishers with a minimum firefighting agent capacity of 0.8 kg
Only extinguishers with the rating 10 BC, 1A 10BC must be equipped with a manufacturer installed pressure charge gauge
The team must present three unused and in date fire extinguishers at the pre inspection
0 C
3 C
1 C
2 C
How wide has the minimum field of vision for the driver to be, while sitting in the car?
200 °
180 °
100°
210°
190 °
Four teams finish the Cost and Manufacturing Event with the following number of points: TEAM A: Winner with 97.5 Points, TEAM B: 88.1 points, TEAM C: 72.8 points, TEAM D: 60.5 points, TEAM E: 55.0 points. However Team B submitted CR documents, which weren't identical to the ones presented on the Cost Event site. Team C forgot to submit an entire assembly, leaving eight partsm 25 processes and 10 materials unassigned and team D did not list four assemblies, 10 processes and 8 materials in their DBOM. Team E did not receice penalties. What is the score of Team C
8.6
5.5
9.0
10.3
14.4
3.2
Which material is suited as a firewall for a cooling hose running through the monocoque under the driver's legs
Aluminium without any holes
Aluminium with holes smaller than 8 mm diameter
The material does not matter, if it is sealed
There is no firewall needed
Aluminium grid with a minimal spacing of 2 mm between the strings
{"name":"Quiz 1", "url":"https://www.quiz-maker.com/QPREVIEW","txt":"Test your knowledge on important engineering principles, safety regulations, and practical applications in the field. This quiz covers topics such as fluid mechanics, structural integrity, and safety equipment for vehicles.10 challenging questionsMultiple choice and checkbox formatsIdeal for students and professionals alike","img":"https:/images/course1.png"}
More Quizzes
Mechanical Engineering Quiz
1589
FSG#005_DONE 01.12.2020
15815
ა იცით "საქართველოს ხმად" აღიარებული ჰამლეტ გონაშვილის შესახებ
840
Python if clause - take the quiz
520
Special Forces - Which Unit Are You? Free
201022230
Are You a Blood or a Crip? Personality
201021181
Never Have I Ever: Which Character Are You? - Free
201019932
3F1 AFSC Readiness - Air Force Mortuary & Honor Guard
201025560
Socialism in Europe - Free History Challenge
201022957
Year 7 Lab Equipment - Free Online
201026825
Do I Have Broken Heart Syndrome? Free & Self‑Check
201019828
Which Statement Describes Binary Star Systems? Free
201019328