Mock Quiz
Engaging Automotive Knowledge Quiz
Test your knowledge in automotive regulations and design standards with our engaging mock quiz! Challenge yourself with multiple-choice questions covering crucial topics that every automotive enthusiast should know.
Sharpen your skills and prepare for competitions or academic assessments. Key features include:
- Detailed questions
- Instant feedback
- Educational insights
Missed Presentation Session with less than 48 hour notice:
10 points
50 points
25 points
20 points
The bodywork in front of the front wheels must have a radius of ______ extending at least 45° relative to the forward direction, along the top, sides and bottom of all affected edges.
At most 10 mm
At least 28 mm
At least 38 mm
At most 45 mm
Documents must be named as :
Team#_TeamName_FBV-DocumentName_Year_V#
Team#_TeamName_FBV-DocumentName_Year
TeamName_FBV-DocumentName_Year_V#
Team#_TeamName_DocumentName_Year_V#
The shutdown circuit directly controls :
All electrical power to the ignition and fuel injectors
All electrical power to the ignition, fuel injectors and all fuel pumps
All electrical power to the ignition and all fuel pumps
Electrical controls to the ignition, fuel injectors and all fuel pumps
Each team must have at least two dry chemical/dry powder fire extinguishers with a minimum firefighting agent capacity of :
0.9 kg
1L
0.5L
1.2L
Each team must have a removable device (called the quick jack) that lifts up the vehicle, so that all driven wheels are ____off the ground and the vehicle is adequately supported
Above the ground
At most 50 mm
At least 50 mm
At least 100 mm
Sensors must not exceed the_____ (measured at the height of the hubs).
front wheel
length of the rear axle
width of the front axle
width of the rear axle
To detect hard braking, the threshold must be chosen such that there are no locked wheels and the brake pressure is :
= 10 bar.
= 30 bar.
� 15 bar.
� 30 bar.
Adjustable tie-rod ends must be constrained with a ____ to prevent loosening.
Jam nut
Washer and nut
Hex nut
Cap nut
Any aerodynamic device must be able to withstand a force of 200 N distributed over a minimum surface of 225 cm2 and not deflect ____ in the load carrying direction
Less than 5 mm
Less than 10 mm
More than 20 mm
More than 10 mm
For Finger guards, Mesh or perforated material may be used but must prevent the passage of a _____ object through the guard
5 mm radius
10 mm diameter
12 mm diameter
12 mm radius
Any portion of the roll bar, roll bar bracing or chassis which might be contacted by the driver's helmet must be covered with a _________ of padding which meets SFI spec 45.1 or FIA 8857-2001.
Minimum width of 12 mm
Minimum thickness of 12 mm
Maximum thickness of 12 mm
Minimum thickness of 10 mm
Both a and b
The tab or bracket to which any harness is attached must have :
Thickness of 1.5 mm
A maximum thickness of 1 mm.
A minimum thickness of 1 mm.
A minimum thickness of 1.6 mm.
The length of the autocross track is :
11 km
Less than 1.5 km
75m
1.5 km
TMax is _____ the time of the fastest vehicle including penalties in Skidpad scoring.
1.25 times
1.5 times
25 times
2 times
{"name":"Mock Quiz", "url":"https://www.quiz-maker.com/QPREVIEW","txt":"Test your knowledge in automotive regulations and design standards with our engaging mock quiz! Challenge yourself with multiple-choice questions covering crucial topics that every automotive enthusiast should know.Sharpen your skills and prepare for competitions or academic assessments. Key features include:Detailed questionsInstant feedbackEducational insights","img":"https:/images/course8.png"}