Rulebook Mock 2

Official announcement comes under

General officials authority

Administrative regulations

Static events

Both A and B

6. BOTS switch must be installed so that in the event of a failure in ________ of the brake circuits the brake pedal over travel will result in the shutdown circuit being opened.

a) At least two

b) At most one

c) At least one

d) At most one

16. All aerodynamic devices ¬_____ from the ground and further rearward than the front axle, must not be wider than a vertical plane touching the most outboard point of the front and rear wheel/tire.

a) Lower than 500mm

b) More than 500mm

c) Lower than 450mm

d) Higher than 450mm

20. Any aerodynamic device must be able to withstand a force of _____ distributed over a minimum surface of _____ and not deflect more than ____ in the load carrying direction.

a) 100N , 225cm²,15mm

b) 200N,250cm²,15mm

c) 150N , 225cm², 10mm

d) 200N, 225cm², 10mm

Liability waiver is required to be signed by

A. The faculty advisor

B. Team members

C. Each team member including faculty advisor

D.Anyone below 18yrs.

-Quick jack must be able to lift the driven wheels upto ______

a. 75mm

b. 100mm

c. 50mm

d. 20mm

The device must trigger due to an omni-directional peak acceleration of ___ g for a half sine test pulse of ≥50 ms length.

a) ≤6

b) ≤13

c) ≤20

d) ≤8

. sensors may be mounted with a maximum distance of ____ above the ground and less than ____forward of the front of the front tires.

a) 500mm / 750mm

b) 300mm / 750mm

c) 500mm / 700mm

d) 450mm / 600mm

The throttle must be actuated mechanically by a foot pedal-

a) via a cable or a tod system

b) via many cables or a rod system

c) none

d) via a e-wire or a rod system

The ETC system must be equipped with at least-

a) APPs and TPS

b) APBs and 2TPS

c) APPs and 2TPS

d) APPs and O2 Sensor

For perimeter shear test the sample must be at least –

a. 50 X 50 (mm)

b. 25 X 150 (mm)

c. 100 X 20 (mm)

d. 100 X 100 (mm)

In double lug joint, each lug must be –

a. Greater 4mm thick and bolt must be 10mm metric grade 12.9 minimum

b. At least 4.5mm thick and bolt must be 10mm metric grade 8.8 minimum

c. At least 4.5mm thick and bolt must be 6mm metric grade 8.8 minimum

d. At least 4.5mm thick and bolt must be 10m metric grade 8.8 minimum

If IA assembly is not welded to chassis then-

a. We are unable to clear IAD document

b. A minimum of eight 8 mm metric grade 8.8 bolts must attach the IA assembly to the front bulkhead.

c. A maximum of eight 8 mm metric grade 8.8 bolts must attach the IA assembly to the front bulkhead

d. A minimum of eight 6 mm metric grade 8.8 bolts must attach the IA assembly to the front bulkhead

Any tubing with a wall thickness less than 1.2 mm or a minimum area moment of inertia less than ------------ mm4 is considered non-structural and will be ignored when assessing compliance to any rule regarding the vehicle structure.

6615

6645

6695

6685

If the CRD is not identical with the uploaded version…

A. It is not evaluated

B. Elimination from the cost event

C. Deduction of 5 points from the cost event score

D. None of the above