FSG#119_DONE 26.12.2020

A detailed engineering scene with automotive designs, showing a car on a racetrack, mechanical tools, and diagrams of aerodynamics and thermodynamics, all in a dynamic and engaging style.

Engineering Mastery Quiz

Test your knowledge in engineering and automotive design with our comprehensive 16-question quiz! This quiz covers various topics including materials science, aerodynamics, and thermodynamics, making it ideal for students, professionals, and enthusiasts alike.

Challenge yourself and ensure you're up to date with key principles:

Mechanical properties and tensile strength
Aerodynamic concepts and vehicle dynamics
Thermodynamics and energy systems

16 Questions4 MinutesCreated by DrivingEngineer247

1.Your first driver has finished his first run of the skidpad event without any OC and has abandoned the second run before entering the second circle of the second run due to mechanical problems. How much timed distance has he covered in meters?

A) 229

B) 172

C) 344

D)212

2.Which of the following materials would withstand greater stress in tensile test? Both compounds have the same amount of matrix.

A)A

B)B

C)SAME

3.Which of the following is true:

A) People in the dynamic area may wear closed-toe shoes

B) Alluminium wheel nuts may be hard anodized and in pristine condition, in order to be used.

C) The IA must be at least 3.94in high and 0.66ft wide for a minimum distance of 0.22yds forward of the front bulkhead.

D) Scatter shields must be constructed of perforated 2mm steel or 3mm alluminium alloy 6061-T6.

5. If the volume of the plenum is 5% larger than the volume of the air intake runner system, can it be placed anywhere upstream the throttle body:

A) Yes

B) No

C) Not enough info

6.A machine needs a damping machine to minimize the vibrations transferred to the ground of the workshop. Initially they wanted to design the system with frequency ratio equal to three. They estimated that the induction frequency to be equal to 25 Hz, however after the first tests they found out the frequency ratio was 1.2. The only choice they had was to select the damping coefficient to be equal to 0.4*natural frequency. Determine the value of C of the system. Consider the machine as a single degree of freedom with mass m=20kg. (Round up in two decimals, g=9.81m/s^2, use “.” as decimal separator)

7.If an object has a weight of 10 lbf on the moon, what would the same object weigh on Jupiter?

A) 139lbf

B) 137lbf

C) 61 kg

D) 62 kg

8. An inventor claims to have invented a device which absorbs 2500 Btu of heat and produces 2000 Btu of work. If the heat sink for the device is ice water (32 F), what would be the minimum source temperature?

A) 2005 (F)

B) 2020 (F)

C) 1093.33 (C)

D) 1090.24 (K)

13.Which is the exact meaning of the symbol here represented:

A) roughness: 5 µm, machining allowance: 1,6 mm

B) roughness: 1,6 µm, machining allowance: 5 µm

C) roughness: 1,6 µm, machining allowance: 5 mm

D) roughness: 1,6 µm, flatness: 5 µm

E) roughness: 1,6 mm, machining allowance: 5 mm

14.Which of the following is not true:

A) Concerning the autocross event: Hairpin Turns: Minimum of 9.84 (yards) outside diameter (of the turn).

B) Passing zones can be situated on either the left or right of the fast lane.

C) After leaving the track the vehicle should be powered down.

D) If a puncture occurs on the endurance event due to severe loss of air in the tyre the vehicle will be scored DNF.

15. Which of the following magnitudes is plotted? Consider only the rear wing and the endplates.

A. Static pressure (Red max, Blue min)

B. Dynamic pressure (Blue max, Red min)

C. Z velocity (Blue max, Red min)

D. Total pressure (Red max, Blue min)

16.Which of the following is not true:

A) All aerodynamic devices rearward of a vertical plane through the rearmost portion of the front face of the driver head restraint support, excluding any padding, set to its most rearward position must be lower than 1,2m from the ground, without the driver.

B) Positive locking mechanisms can include nylon lock nuts of ISO10512 and locking plates.

C) The background shape of the vehicle number can be square or rectangular.

D) The application of absorbent materials on the outside of the exhaust manifold is not permitted.

FSG#119_DONE 26.12.2020

Engineering Mastery Quiz

More Quizzes