EXIT EXAM

Create an image of a civil engineer standing in front of a construction site with blueprints in hand, surrounded by cranes and buildings under construction, with a clear blue sky.

Civil Engineering Exit Exam Quiz

Test your knowledge with our comprehensive Civil Engineering Exit Exam Quiz designed for aspiring professionals in the field. This quiz consists of 30 questions that cover a wide range of topics including structural analysis, materials engineering, traffic management, and project management.

Challenge yourself and measure your understanding of crucial civil engineering concepts. You'll encounter:

Multiple-choice questions
Calculations and problem-solving scenarios
Real-world application of engineering principles

30 Questions8 MinutesCreated by MeasuringMind537

A soil has a specific gravity of 2.68 and a void ratio of 0.73 if the degree of saturation is 92%. Compute the dry density of the soil in g/cc

A plain round bar made out of steel weight 0.5kg with dimensions of 155 mm in diameter and 1.5m in length calculate for its density in g/cc

What is the effect of staggered holes in steel tension members?

Increases the tensile strength of member

Does not affect the tensile strength of member

Halves the tensile strength of member

Reduces the tensile strength of member

It is A govenrment policy covering technical requirements in constructing or renovating building and structures in the Philippines to secure the life, health, property and welfare of Filipinos

National Structural Code

Presidential Decree 1096

Architectural and structural plans

Building permit requirement

The branch of engineering that deals with improvement of traffic performance, traffic studies and traffic network is called?

Traffic engineering

Traffic management

Railway engineering

Highway engineering

A floor joist 50mm x 200mm has a span of 5m. If it carries a total floor load of 5kPa. Determine the spacing joist in mm to develop a bending stress of 8MPa.

270mm

120mm

170mm

150mm

An open channel to be made of concrete is to be designed to carry 5m3/s at a slope of 0.000655. Find the most efficient cross section for (a) semicircular section (solve for the diameter in m)

1.847m

1.645m

1.457m

1.954m

Reservoir A has an elevation of 300mm circular pipe is connected to it with diameter of 300 mm and length of 200 m, while reservoir B is at an elevation 200 mm with circular pipe connected to it diameter 250mm and length of 250 m and Reservoir C elevation with a circular pipe attached to it, diameter is 600 mm and length of 450mm. All pipes meet at junstion. Determine the flow rate in Pipe A in m3/s. Use f=0.02

0.745 m3/s

0.992 m3/s

0.224 m3/s

0.994 m3/s

Locational clearance requirements in acquiring building permit are the following except:

Architectural plan

Site development plan

Foundation plan

Lot plan

If super elevation is not provided on a horizontal curve of a highway, then on which portion of the road are pot holes likely to develop?

Center of road

Outer edge of the road

Inner edge of the road

Shoulder of the road

The maximum super elevation to be provided on the road curve is 1 in 15. If the rate of change of super elevation is 1 in 120 and the road width is 10 m, then the minimum length of the transition curve on either end will be:

180m

80m

125m

30m

A surveying student walked along a given line that was known to be 200.0 ft long to determine her average unit pace. She paced the line four times, recording 78, 76.5, 77 and 76 paces, respectively, in her field book. If the surveyor then counted on average of 123.5 paces while pacing off a line of unknown distance, what is the distance?

325.70 ft

321.30 ft

320.25 ft

328.30 ft

A curving roadway has a design speed of 80 km/hr. At one horizontal curve, the superelevation has been set at 6% and the angle of side fraction is found to be 6o. Determine the impact factor

0.19

0.17

0.20

0.16

If civil engineers inform the client via document about a certain change involving site implementation then civil engineers can already implement the change with or without the approval of the client.

True

False

A summit curve is formed at the intersection of a 3% up gradient and 5% down gradient. To provide a stopping distance of 128m, the length of summit curve needed will be:

298 m

322 m

271 m

340 m

In general, it is the densification of soil by removal of air, which requires mechanical energy

Compaction

None of the above

Consolidation

Compression

Metropolitan Manila has a road network following which type of road pattern?

Radial or Circular Pattern

Rectangular Pattern

Hexagonal Pattern

Radial or Star Pattern

It is the minimum distance required to stop a vehicle before it reaches a stationary object.

Decision Sight Distance

Stopping Sight Distance

Passing Sight Distance

Intersection Sight Distance

In Project Management, it refers the sequence of the project network activities which add up to the longest overall duration. This determines the shortest time possible to complete the project

Risk

Critical Path

Scheduling

None of the above

Calculate the steel ratio that will produce a tension-controlled failure if compressive strength f'c = 28 MPa and steel yield strength fy

0.02167

0.03258

0.04567

0.02617

It is an uncertain event or condition that, if it occurs, has a positive or negative effect on one or more project objectives such as scope, schedule, cost, and quality.

Critical Path

All of the above

Risk

Scheduling

EXIT EXAM

Civil Engineering Exit Exam Quiz

More Quizzes