C8

1What type of gasket is used on high pressure steam flange joints?

2When using a chisel, you should _____.

3 Before boring a blind tapered hole, a good shop practice to follow is to _____.

4Which of the following types of files will produce a fine finish when draw filing?

5Mill files are always _____.

D 6Heavy pressure on the ends of a file will cause the work surface to become _____.

7A new file should be broken in carefully by filing a piece of _____.

8 The proper use of a flat chisel is for cutting _____.

9Which of the chisels listed should be used for cutting oil grooves?

10 Before boring a blind tapered hole, a good shop practice to follow is to _____.

11Which of the following types of files will produce a fine finish when draw filing?

12 Pinning is often caused by _____.

13Heavy pressure on the ends of a file will cause the work surface to become _____.

14A new file should be broken in carefully by filing a piece of _____.

15 The terms rough, coarse, bastard, second cut, smooth and dead smooth refer to the _____.

16A file coated with oil and stowed away will _____.

17 Pushing the file endways (or with axis), under pressure, against the work, is called _____.

18When cutting with a handheld hacksaw, you should apply downward pressure on the hacksaw frame _____.

19A hacksaw blade with 14 teeth per inch should be used to cut _____.

20 The type of tooth set on a hacksaw blade where every third tooth remains straight, while the other two are alternately set is known as _____.

21 To finish tapping a blind hole, it is best to use a _____.

22A taper tap is correctly used for _____.

23 Round split dies are usually adjustable to _____.

24A thread die will be easier to start if the end of the shaft to be threaded is slightly _____.

25 Round split dies are usually adjustable to _____.

26 The type of tooth set on a hacksaw blade where every third tooth remains straight, while the other two are alternately set is known as _____.

27A hacksaw blade with 14 teeth per inch should be used to cut _____.

28A hacksaw blade will start a cut more easily if you _____.

29Which of the following types of files will produce a fine finish when draw filing?

30 If you are cutting external threads by hand and you start the die at an angle, the threads will _____.

31A file coated with oil and stowed away will _____.

32 The tang of a file is the part that _____.

33 Pinning is often caused by _____.

34A Reed and Prince screwdriver should be used only on a Reed and Prince screw, and a Phillips screwdriver should only be used on a Phillips screw in order to avoid damaging the _____. I. tool II. screwhead

35One of the steps required to increase the drilling speed of a drill press is to _____.

36 .A thread die will be easier to start if the end of the shaft to be threaded is slightly _____.

37 The term referring to the amount or degree the teeth of a hacksaw blade are pushed out or canted from the blade center is known as _____.

38A taper tap is correctly used for _____.

39 Pushing the file endways (or with axis), under pressure, against the work, is called _____.

40 Rapid wear on the extreme outer corners to the cutting edges of a drill bit is the result of the drill having _____.

41 Some heavy duty screwdrivers are made with a square shank to _____________.

42 Pipe threads are made with the use of __________.

43A side from welding, the best material to use in bonding pipes carrying low temoerature liquids or fluids is _____________.

44 The type of force that tends to move toward the center is ______________.

45Which among the cutting tool materials retains the lowest wear resistance when the tool bit is used in machining hard metal materials through the modern center lathe machine onboard?

46 Cutting tools in a shaper can also be used in a ___________.

47Which of the following involves the shaping of metals usually into a rod or tube cross section, by forcing a block of material through appropriate shape disc?

48Which of the parts of the center lathe listed below is needed to turn a right head thread into a left head thread?

49How do you make it easier for a hand hacksaw to cut a work piece?

50One of the steps required to increase the drilling speed of the drill press is to _____________.