Engineering Compliance and Technical Knowledge Quiz

An engineering-themed illustration showing technical diagrams, gears, and formulas in a modern design.

Engineering Compliance and Technical Knowledge Quiz

Test your understanding of engineering compliance and technical principles with our comprehensive quiz. Designed for students and professionals alike, this quiz will challenge your knowledge on various topics, including technical specifications, safety regulations, and engineering fundamentals.

Key features:

Multiple choice questions
Focus on practical applications and rules
Instant feedback on your answers

14 Questions4 MinutesCreated by AnalyzingBolt301

1.Which statement is in compliance with the rules?

Where more than one exhaust outlet is present, the test will be repeated for each exhaust and the average reading will be used.

A completed DSS must be submitted on the event's start.

Burnouts prior to and during the events are prohibited.

4.5 points are awarded to every team that finishes at least one run without DNF or DQ in skidpad.

2.A team missed the initial deadline for SESA document and submitted this 49 hours after the deadline. After that the team got an official request to make a correction of this document and missed the given deadline of 168 hours and upload the revised version 172 hours too late. What total penalty will the team receive for the submission of this document?

30 points

De-registration

65 points

100 points

3.Which statement is in compliance with the rules?

Vehicles may not be presented for design judging without having passed technical inspection.

All suspension mounting points must be visible at technical inspection only by direct view.

All onsite participants can sign a liability waiver upon registering on site which can be found on the competition website.

None.

4.The following capacitor has relative permitivity ε=2.1, Plate area S=0.5cm^2 and distance between plates d=1.2mm. What is the capacitance of the capacitor in uF?

7.847

7.474

7.747

7.774

5.The upper support member of the front bulkhead:

Must be attached to the front bulkhead a maximum of 50 mm above the top-most surface of the front bulkhead.

Must be attached to the front bulkhead a maximum of 50 mm below the top-most surface of the front hoop.

Must be attached to the front bulkhead no more than 50 mm above the top-most surface of the front bulkhead.

Must be attached to the front bulkhead no more than 50 mm below the upper surface of the front bulkhead.

8.Which of the following is/are not true about BPP?

The team members who have been introduced must answer the judges’ questions even if they were not actually presenting.

Any presentation exceeding ten minutes will carry on with a penalty of 5 points for any additional minute.

Three members must present the BPP.

Your team made it to the BPP finals and scored 70.9 points.

9.At a very low temperature, a semiconductor:

Becomes a conductor

Becomes an insulator

May become a conductor or an insulator

Will remain a semiconductor

10.Your team missed the following items from the BOM: Front Uprights and a layer of Pre-Preg on a part. What’s the total penalty?

11.When the driver sees a red and yellow striped flag,he/she must:

Exit the track at the first opportunity

Pull into the driver change area for a mechanical inspection of the vehicle

Come to an immediate safe and controlled stop on the track and must follow track marshals directions

Be prepared for evasive maneuvers to avoid a difficult situation on the track

12.A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters respectively equal to 40 and 60 mm. What is the largest torque that can be applied to the shaft if the shearing stressis not to exceed 120 MPa?

3.68 kN*m

4.08 kN*m

4.23 kN*m

6.32 kN*m

13.Which statement is in compliance with the rules?

The fuel tank must have a provision for emptying if required.

Minimal openings around the front suspension are allowed.

Any welded seams shape should not be mechanically altered in any way.

None.

14.What is an SCR?

A PNPN thyristor with 3 terminals

A PNPN thyristor with 4 terminals

A PNP thyristor with 3 terminals

A NPN thyristor with 3 terminals

Engineering Compliance and Technical Knowledge Quiz

Engineering Compliance and Technical Knowledge Quiz

More Quizzes