FSEast DV 2019

A detailed illustration of an engineering design event featuring various teams showcasing their vehicles, with a dynamic racetrack in the background and judges evaluating designs at a podium.

FSEast DV 2019 Engineering Design Quiz

Test your knowledge on the Engineering Design Event at FSEast 2019! This quiz covers various aspects of the event, including rules, vehicle dynamics, materials, and cost reports.

Challenge your understanding of engineering principles.
Learn about vehicle performance metrics.
Engage with fellow engineering enthusiasts.

15 Questions4 MinutesCreated by EngineeringEagle42

Can a team be eliminated from the Engineering Design Event by the judges, if every document of theirs was accepted and they are present at the Engineering Design Event?

Yes, if the judges consider the vehicle to be in unfinished state.

No, if a team is present at the event, the judges are obligated to evaluate their performance.

Yes, if the team did not pass any scrutineering prior.

Yes, if the judges consider the number of the team members present at the discussion insufficient.

Which of the following dynamic disciplines will be organized first time in 2019 at FS East?

Driverless AutoX Event

Trackdrive Event

Driverless Skidpad Event

AutoX Event

In which Cost Report Document does the team need to list the research and developement costs?

In the DBOM

In neither of the Cost Report Documents

In the Cost Explanation File

In the CBOM

The circular Dynamic Platform at ZalaZone has 1% of slope from North to South. The diameter of the Platform is 300 m. If a ball is released on the highest point of the Platform (North), from standstill state, what will be the speed of the ball at the lowest point of the Platform (South)? Consider that the ball rolls directly from the highest point to the lowest point. Rolling resistance is 0 Mass of the ball is 200g G = 10 m/s²

5,897 km/h

7,7459 m/s

7,7459 km/h

5,897 m/s

If a thin and infinitely long fibre's diameter is reduced, which of its properties from the following will increase?

Peak force at failure

Strength

Young modulus

Stiffness

Our vehicle completes the Acceleration Event. Its velocity is 126km/h, when it crosses the finish line. How much time did it need to complete the run, if we assume, that its acceleration is constant during the run?

4,28s

3,86s

4,56s

A car finishes the skidpad event with an average laptime of 5,0 seconds. The static friction coefficient of the ground and the tire is 0,9. What was the aerodynamic downforce to weight ratio during the run? Assume, that the car is travelling on the centerline of the track. G=9,81 m/s²

0,5

0,45

0,9

1,35

Which of the following requirements is a must for all types of vehicles, when moving the vehicle on the competition site other than on the practice or competition tracks?

Detached master switch.

A registered driver wearing the required driver equipment as defined in T 13.3 except for helmet, arm restraints and balaclava having full control of steering and braking

Two team members walking on either side of the vehicle.

Vehicles must be pushed at a normal walking pace by means of a red pushbar, equipped with a fire extingusher.

Which of the listed material can be described with the following fictional mechanical properties? Specific strength (σ[MPa]/ϝ[g/cm³]) = 1656 Specific modulus (σ[GPa]/ϝ[g/cm³]) = 57 Failure Strain (%) = 1,8

Titanium

Aramid Fiber Reinforced Polymer

Steel

Carbon Fiber Reinforced Polymer

According to the FS Rules 2019, how many points will a team score eventually on the Cost and Manufacturing Event, if the team is not in the final, the score awarded to a team during the initial judging is 79 points, while the highest score awarded to any team not participating in the finals is 91 points?(

82,5

86,8

What does the yellow and red striped flag mean during Endurance and Autocross Event?

The driver must pull into the driver change area for discussion with the officials concerning an incident. A time penalty may be assessed.

Mechanical black flag. The driver must pull into the driver change area for a mechanical inspection of the vehicle, something has been observed that requires a closer inspection.

The track is slippery or something is on the racing surface that should not be there. The driver must be prepared for evasive maneuvers to avoid the situation.

How many different light combinations are possible on a driverless vechicle with the indicator lights defined in rules? (Only by color)

The Zalazone Proving Ground would contain several track elements (such as Dynamic Platform, Slopes, Handling Course etc.) In which phase of the construction it is planned to contruct the High - Speed Oval Track element?

Phase 1

Phase 2

Phase 3

Phase 4

FSEast DV 2019

FSEast DV 2019 Engineering Design Quiz

More Quizzes