Formula Bharat Practice Quiz 2
Formula Bharat Practice Quiz 2
Test your knowledge and understanding of the rules and regulations pertinent to Formula Bharat! This practice quiz is designed for teams and enthusiasts eager to refine their knowledge before the competition.
Features:
- 15 multiple-choice questions covering various technical and procedural aspects.
- Instant feedback on your answers.
- Ideal preparation for competition participants.
Which of the following is true?
Plastic brake lines are prohibited
Atleast two full threads must project from any nut.
Compressed gas cylinders should be lower than driver’s shoulder level.
None of the above
Which of the following is true?
TS components cannot use oil as a coolant
Any part of lubrication system cannot be below the line joining the lowest point of main hoop and the lowest chassis member behind the lubrication system.
Mounting of aero devices is considered as an aerodynamic device.
None of the above
How The anti-submarine belts of a 6 point harness should be mounted for making it rule compliant?
With the belts going vertically down from the groin, or angled up to 20° rearwards. The anchorage points should be approximately 100 mm apart.
With the anchorage points on the primary structure at or near the lap belt anchorages, the driver sitting on the anti-submarine belts and the belts going down around the groin to the release buckle.
Both 1 and 2
Any one of them(Constraint only one method can be used).
Which of the following is relevant for lap belt mounting
In side view, the lap belt must be capable of pivoting freely by using a shouldered bolt and an eye bolt attachment.
Where the belts or harness pass through a hole in the seat, the seat must be grommeted
The lap belts should not come through the seat at the bottom of the sides of the seat
The lap belts must be routed over the sides of the seat
The last upload of a video is possible 168 hours (7 days) after the VSV deadline (max. 49 penalty points). Teams without a video at this point will be de-registered from the competition. A re-entry will not be possible(without any correction requests)
True
False
For the design Event which of the following is true?
Vehicles must be presented for design judging in finished condition, fully assembled, complete and ready-to-drive.
Vehicles may be presented for design judging without having passed technical inspection,accumulator inspection even if final tuning and setup is in progress.
Any spare accumulator cells or spare stacks may be presented.
Evidence of information mentioned in the EDR should be brought.
Which of the following is true?
Team members who have graduated within the seven month period prior to the competition remain eligible to participate.
The participate must be above or equal to 18 year old.
Faculty Advisors may assist in the preparation,testing or operation of the vehicle.
Substitution of driver harness after inspection is allowed.
Repeated actuation of the brake over travel switch must close the shutdown circuit, and it must be designed so that the driver cannot reset it.
True
False
Mark the statement which is not TRUE for LVS and its components.
The maximum permitted voltage that may occur between any two electrical connections in the LVS is 60 V DC or 25 V AC RMS.
The LVS must be grounded to the chassis.
LV batteries must be protected from short circuits, at least more than 100 mm from ungrounded terminals.
If an implausibility occurs between the values of the APPSs and persists for more than 0.1s, the power to the motor(s) must be immediately shut down completely.
All electrical systems need not have appropriate overcurrent protection.
True
False
The following are TRUE regarding overcurrent protection except?
The continuous current rating of any electrical component must not be less than the continuous current rating of the overcurrent protection.
All overcurrent protection devices which are part of the TS must not rely on programmable logic.
If multiple pins of a connector are used to carry currents in parallel, each pin need not be appropriately protected.
The overcurrent protection must be designed for the expected surrounding temperature range but at least for 0°C to 85°C.
Every housing or enclosure containing parts of the TS system, must be labelled with reasonably sized sticker(s) according to “ISO 7010-W012” (red spark on a white-edged blue triangle).
True
False
For a system with maximum TS voltage 168V, where both TS and LVS are present within an enclosure the spacing through air, or over a surface can not be-
20 mm
10 mm
25 mm
30 mm
The TS may not comply with-
In side or front view any part of the TS must not project below the lower surface of the chassis.
All TS components used must have positive interlock feature.
All TS wires must be marked with wire gauge, temperature rating and insulation voltage rating or a serial number/norm printed on the wire if clearly bound to the wire characteristics.
Using only insulating tape or rubber-like paint for insulation is prohibited.
Which of the following is false
The driver change time is started is soon as the vehicle is stopped in driver change area.
Including ESO only 3 members can enter the driver change area.
Running order for endurance will be published in the competition website.
None of these
{"name":"Formula Bharat Practice Quiz 2", "url":"https://www.quiz-maker.com/QPREVIEW","txt":"Test your knowledge and understanding of the rules and regulations pertinent to Formula Bharat! This practice quiz is designed for teams and enthusiasts eager to refine their knowledge before the competition.Features:15 multiple-choice questions covering various technical and procedural aspects.Instant feedback on your answers.Ideal preparation for competition participants.","img":"https:/images/course8.png"}