RuleBook Quiz-1

Conditions. If so, the tires need to be treaded or grooved compliant to Choose the correct statement in accordance to the above line
he tread pattern or grooves were molded in by the tire manufacturer or were cut by the team or their appointed agent.
With least tread depth of 0.024 m
Tires in violation of compilation or with treads/grooves are considered “wet” tires.
Tires in violation of compilation or with treads/grooves can be considered as dry tires
Exposed rotating final drivetrain parts, such as gears, clutches, chains and belts must be fitted with scatter shields. Scatter shields and their mountings must Be constructed of non-perforated _mm steel or _ mm aluminum alloy 6061-T6. Be attached with __mm metric grade __or stronger.
2,3,6,8.5
2,3,6,8.8
3,4,6.6,8.8
3,4,6,8
The TS and LVS are on the same PCB, they must be separate well defined areas of the board and if the over surface, Through Air(cut in board), Conformal coating are the roots of the cubic equation x^3 – 11.6(x^2)+39.68(x)-40.96=0 then which of the following statements are true
The voltage value is between 0 V DC to 50 V DC
The voltage value is between 50 V DC to 150 V DC
The voltage value is between 150 V DC to 300 V DC
The voltage value is between 300 V DC to 600 V DC
In skidpad event event, if teams run time is 1.2 times of fastest vehicle run time without DNF and DQ , Then what would be total skidpad scoring for the team.
10.80
14.30
15.30
55.92
Consider the below statements and choose the correct option below :-  Prior to the competition, all teams must submit clearly structured documentation of their entire electrical system (including control and TS) called the ESF.  The response value of the IMD must be set to ≥200 Ω /v, related to the maximum TS operation voltage.  According to “ISO 7010-W012” the triangle is with black lightning bolt on green background.  The overcurrent protection must be designed for the expected surrounding temperature range but at least for 0°C to 85°C.  The TS is active if any of the AIRs or the pre-charge relay is opened.  The AIRs must be of a “normally open” type. Solid-state relays are prohibited.  AMS signals are system critical signals.
Number of correct statements are less than number of incorrect statements.
Number of correct statements are more than number of incorrect statements.
Number of correct statements are equal to number of incorrect statements.
Number of correct statements are 3.
Which of the following is /are true about dynamic event
Driving off-site is allowed
To use the practice track, vehicles must have passed all technical inspections
Drivers must wear the dynamic vest when sitting in the vehicle
The ground clearance can be tested at any time.
5)How many signals below are SCS(signal critical signals)  Signals influencing the TSAL.  The Signals controlling the red indicator light in the cockpit and clearly marked with the lettering “AMS”.  All signals influencing the shutdown circuit.  The Signals controlling the red indicator light in the cockpit and clearly marked with the lettering “IMD”.  All signals in the charger shutdown circuit.  The APPS Signals
3
4
6
5
The driver is completely seated, hands on the attached steering wheel, and wearing the relevant driver equipment, drivers must be able to escape to the side of the vehicle in feasible time of
0.133 mins
0.15 mins
0.075 mins
0.092 mins
Which of the following are incorrect
There will be no penalties applied for participating as a second year vehicle.
1 correction is allowed from V2,2 corrections are allowed from V3.
De-registered team which sucessfully challenged de-registration can get 60 points in BPP
Only one team per university is allowed in FB competition
To prevent the driver from being able to touch any sections of the car with a surface temperature exceeding 60°C, enough heat insulation must be offered. The insulation might be mounted outside the cockpit or built into the firewall or driver's seat. The demands for this can be
a material that is heat-resistant and conductivity-insulating and has a thickness of 7 mm.
Insulation by convective heat transfer having a coefficient of (3-22) W/m2 and thickness of 29.5mm
A solid metal heat shield with a thickness of 0.3 mm
None of the above
{"name":"RuleBook Quiz-1", "url":"https://www.quiz-maker.com/QC5SANO7Q","txt":"Conditions. If so, the tires need to be treaded or grooved compliant to Choose the correct statement in accordance to the above line, Exposed rotating final drivetrain parts, such as gears, clutches, chains and belts must be fitted with scatter shields. Scatter shields and their mountings must Be constructed of non-perforated _mm steel or _ mm aluminum alloy 6061-T6. Be attached with __mm metric grade __or stronger., The TS and LVS are on the same PCB, they must be separate well defined areas of the board and if the over surface, Through Air(cut in board), Conformal coating are the roots of the cubic equation x^3 – 11.6(x^2)+39.68(x)-40.96=0 then which of the following statements are true","img":"https://www.quiz-maker.com/3012/images/ogquiz.png"}
Powered by
Quiz Maker
Powered by: Quiz Maker