FB QUIZ 5 June

Create an engaging and informative image depicting various vehicle safety features, such as emergency shutdown systems, wiring standards, and fire extinguisher placement in vehicles.

FB QUIZ: Vehicle Safety Standards

Test your knowledge on vehicle safety standards with our comprehensive quiz! Challenge yourself on topics such as shutdown buttons, inertia switches, BSPD compliance, and more. See how well you understand the regulations that keep vehicles safe on the road.

Multiple-choice questions
Score your knowledge
Learn about vehicle safety requirements

15 Questions4 MinutesCreated by TestingTurtle47

Which is not TRUE for shutdown buttons?

A) A system of three shutdown buttons must be installed on the vehicle.

B) Each shutdown button must be a push-pull or push-rotate mechanical emergency switch.

C) The minimum allowed diameter of the shutdown buttons on both sides of the vehicle is 40 mm.

D) Shutdown buttons must be rigidly mounted to the vehicle and may be removed during maintenance.

The inertia switch used must trigger due to a uni-directional peak acceleration of ≤8 g for a half sine test pulse of ≥50 ms length and ≤13 g for a half sine test pulse of ≥20 ms length.

A) True

B) False

The BSPD does not comply with-

A) A standalone non-programmable circuit, the BSPD, must not open the shutdown circuit when hard braking occurs and <=5 kW power is delivered to the motors.

B) The BSPD must be directly supplied from the LVMS.

C) The action of opening the shutdown circuit must occur if the implausibility is persistent for more than 0.5s.

D) Supply and sensor signals can be routed through any other devices before entering the BSPD.

A test involving, sending an appropriate signal that represents the current, in order to achieve ≤5 kW whilst pressing the brake pedal, must prove the functionality of all the parts of BSPD.

A) True

B) False

What is not TRUE regarding accelerator pedal?

A) It must be possible to separately disconnect each APPS signal wire to check all functionalities.

B) A fully released accelerator pedal must result in a wheel torque of 0 Nm.

C) Implausibility is defined as failure of analog sensor signals transmitted by cable.

D) The foot pedal must return to the 0% position when not actuated.

All the TS cables and wiring must always be located within the rollover protection envelope.

A) True

B) False

The following are TRUE regarding TS wiring except?

A) The temperature rating for TS wiring, connections and insulation must be at least 85°C.

B) Soldered connections in the high current path may be allowed if the connected devices are not cells or wires.

C) All TS wiring that runs outside of TS enclosures must be securely anchored at both ends so that it can withstand a force of 200 N without straining the cable end crimp.

D) All TS connections should not rely on steel bolts to be the primary conductor.

Which of the following is not rule compliant?

A) AFFF fire extinguishers are prohibited.

B) An approved fire extinguisher must be mounted to quick jack such that it is quickly accessible.

C) Hand held fire extinguishers are not permitted to be mounted on or in the vehicle.

D) Dry chemical or dry powder ABC fire extinguishers are acceptable.

Which of the following point is correct for fasteners?

� Any tabs attaching suspension members to the primary structure are required to meet the rule of “e/D” of 1.5 or greater.

� Team that use self-made fastener will need to present documentation with appropriate reasoning, calculations and testing during technical inspection.

� Jam nuts can be considered for positive locking mechanism.

� Bolts, Nuts and other fasteners utilized in driver’s harness can be considered as critical fasteners.

In Autocross the Tmax is __ times the time of the fastest vehicle including penalties.

1.25

1.5

1.33

None

What should be the maximum content of manganese for Steel tubing has to be made from unalloyed carbon steel?

1.2

2.4

1.7

0.4

What are not requirements for the IA assembly when mounted on the vehicle:

Decelerate the vehicle at a rate nThe energy absorbed in this event must meet or exceed 7350 J. Ot exceeding 20 g average and 40 g peak.

Teams using the standard IA are required to submit test data with their IAD Report and all other requirements must be included.

None of theseThe energy absorbed in this event must meet or exceed 7350 J.

None of these

Choose the wrong one:-

Manufacturing cost such as working of machines per hour must be included in BOM.

Will be awarded zero points.

Will be De-registered.

Can make a new time slot accodring to officials

Igned time period will (during presentation prelims)?

Will be awarded zero points.

Get anaother chance at end of event.

Will be De-registered.

Can make a new time slot accodring to officials

If a assembly which consists of 3 parts is mising from BOM, how much points will be deducted?

FB QUIZ 5 June

FB QUIZ: Vehicle Safety Standards

More Quizzes