FB 2020

An infographic showcasing various vehicle safety standards and design principles, emphasizing structural integrity and safety devices.

Vehicle Safety and Design Quiz

Test your knowledge on vehicle safety standards and design specifications with our comprehensive quiz. This quiz consists of 31 questions that cover various aspects of automotive engineering, from safety devices to structural requirements.

Prepare yourself for:

Detailed questions on vehicle construction
Insights into safety protocols
Challenging multiple-choice format

31 Questions8 MinutesCreated by DrivingGuide101

BSPD stands for

Brake system Plausibility Device

Brake System Prevention Device

Binary System Plausibity Device

Binary System Prevention Device

Part of vehicle which provides protection of driver's feet.

Front Hoop

Front Bulkhead

Front Hoop Bracing

Front Bulkhead Support

A removable device that attaches to the rear of the vehicle and allows two people to push and pull the vehicle while standing erect behind the vehicle.

Pushbar

Quickjack

AIP

ABS

This assembly may be single welded structure, double welded structure or a combination of composite and welded structure.The fabricated structure assembly that supports all functional vehicle systems together.

Swing Arm

Chasis

Chasis Member

Front Hoop Bracing

Deformable energy absorbing device located at forward of the front Bulkhead

Front Bulkhead Support

Front Bulkhead Support System

Rollover Protection Envelope

Impact Attenuator

All edges of the bodywork that could come into contact with a pedestrian must have a minimum radius of

1mm

1.5mm

0.85mm

2.5mm

The bodywork in front of the front wheels must have a radius of "R" mm and extend atleast an angle of " ____° " relative to the forward direction along the top sides and bottom of all affected edges.

18mm, 45°

30mm, 50°

38mm, 40°

38mm, 45°

Minimum static ground clearance of any portion of the vehicle, other than tires, including a driver, must be

32mm

31mm

30mm

29mm

Steel Tubing has to be made from unalloyed carbon steel with a maximum content of

0.3% Carbon, 1.7% Manganese and 0.6% other element

0.3% Carbon, 1.2% Manganese and 0.6% other element

0.2% Carbon, 1.7% Manganese and 0.6% other element

0.2% Carbon, 1.2% Manganese and 0.6% other element

If the front hoop is made from multiple pieces, it has to be separated using

Node-node triangulation

Equivalent construction

Both a&b

None

AIP stands for

Active injection Pedal

Accumulator isolation Plate

Anti Intrusion Plate

Accumulator Injection Pedal

Two lines extending vertically from positions 75 mm in front of and 75 mm behind the outer diameter of the front and rear tires in the side view of the vehicle, with steering straight ahead.

Monocoque

Keep out zone

Both a&b

None

Roll hoops must have one ______ hole in a non-critical straight location and its surface at this point must be unobstructed for at least _______°.

4.5 mm , 180

3.5mm, 165

4.5 mm , 180

3.5mm, 165

The main hoop braces must be attached to the main hoop no lower than _____ mm below the top-most surface of the main hoop. The included angle formed by the main hoop and the main hoop braces must be at least _____°

160mm, 30

150mm,45

150mm, 15

130mm,60

Position with a seat back angled at 30° or less from the vertical as measured along the line joining the two 200 mm circles of the 95th percentile male template

Reclined Driving Position

Upright Driving Position

Downward Driving Position

Inclined Driving Position

This switch must be installed so that in the event of a failure in at least one of the brake circuits the brake pedal over travel will result in the shutdown circuit being opened. This must function for all possible brake pedal and brake balance settings without damaging any part of the vehicle. Identify the switch.

BAT Switch

BIT Switch

BFT Switch

BOT Switch

All forward facing edges of aerodynamic devices that could contact a pedestrian must have a minimum radius of ____ mm for all horizontal edges and ____ mm for vertical edges.

5mm, 3mm

5mm,2mm

4mm, 3mm

4mm,2mm

Methods accepted as positive locking mechanisms

Locking plates

Prevailing torque lock nuts

Both a&b

None of these

The engine(s) used to power the vehicle must be piston engine(s) using a four-stroke primary heat cycle with a displacement not exceeding _____ cm3 per cycle.

710

715

725

720

FB 2020

Vehicle Safety and Design Quiz

More Quizzes