Formula bharat quiz

A high-tech formula racing car on a track, with focus on safety features like helmet, harness, and aerodynamic devices, in a vibrant racing environment.

Formula Bharat Safety Quiz

Test your knowledge on safety regulations and guidelines specific to Formula Bharat competitions. This quiz covers critical aspects of vehicle safety and mechanical compliance necessary to ensure a secure racing environment.

Are you familiar with essential safety standards? Challenge yourself with questions related to:

  • Aerodynamic devices
  • Fuel line standards
  • Driver harnesses
  • Performance parameters
15 Questions4 MinutesCreated by DrivingForce42
Which one is incorrect for listing environment to qualify as safe
Driver wearing full protection gear
Rules compliant chassis and mounted IA
Running under low visibility conditions with officials permission
None of the above
Any aerodynamic device must be able to withstand a force of 200 N distributed over a minimum surface of 225 cm2 and not deflect more than __
10 mm in the load carrying direction.
25mm in the load carrying direction.
10 in any direction
Select the Incorrect option
Springs in the TPSs are not acceptable as return springs.
TPS signals indicate the throttle has returned to idle position ±5 % for at least one second.
The maximum restrictor diameters which must be respected at all times during the competitionare for Gasoline fueled vehicles - 25 mm
Select the Incorrect option
All aerodynamic devices forward of a vertical plane through the rearmost portion of the front face of the driver head restraint support, excluding any padding, set to its most rearward position, must be lower than 500 mm from the ground.
All aerodynamic devices lower than 500 mm from the ground and further rearward than the front axle, must not be wider than a vertical plane touching the most outboard point of the front wheel/tire.
All aerodynamic devices rearward of a vertical plane through the rearmost portion of the front face of the driver head restraint support, excluding any padding, set to its most rearward position must be lower than 1.2 m from the ground.
High pressure fuel Lines must be rigidly connected every _ by mechanical fasteners to structural engine components.
50mm
75mm
100mm
A “___” is any tank orvolume that is a significant enlargement of the normal intake runner system.
Exhaust
Intake
Plenum.
Which of these is incorrect
Agents that can be induced into the combustionchamber.
Gasoline
Air
Lubricant
Significant change" is defined as a
A pipe change
A hard point change
Pipe and hard point change
None of the above
In BPP maximum points are awarded for
Pitch deck
Finances
Content
In non-welded driver’s harness attachment, while physical testing of strength of lap belt and shoulder straps attachment edges of the test fixture supporting the sample must be a _____ from the load application point
Minimum of 125mm
Maximum of 150mm
Minimum of 150mm
Maximum of 100m
If the lap belts and anti-submarine belts are attached ________ apart, these must support a total load of 19.5 kN
More than 100mm
Less than 50mm
Less than 100mm
More than 50mm
The roll hoop tubing must not be further away than____ from the inside surface of the lowest part of the primary structure
50mm
30mm
25mm
100mm
The test fixture must support the entire sample, except for a ______mm hole aligned coaxially with the punch. The sample_______be clamped to the fixture.
32, must not
32, must
25, must not
25, must
The roll hoop tubing ______ be further away than_______ mm from the inside surface of the lowest part of the primary structure.
Must not, 30mm
Must, 30mm
Must not, 20mm
Must, 20mm
Minimum jounce
Must be at least 25mm and checked with the driver seated
Must be 25mm and checked with/without driver seated
Must not be more than 25mm and checked with the driver seated
None of these
{"name":"Formula bharat quiz", "url":"https://www.quiz-maker.com/QPREVIEW","txt":"Test your knowledge on safety regulations and guidelines specific to Formula Bharat competitions. This quiz covers critical aspects of vehicle safety and mechanical compliance necessary to ensure a secure racing environment.Are you familiar with essential safety standards? Challenge yourself with questions related to:Aerodynamic devicesFuel line standardsDriver harnessesPerformance parameters","img":"https:/images/course5.png"}
Powered by: Quiz Maker